Maytag MFI2067AE User Instructions - Page 8

Refrigerator

Page 8 highlights

IMPORTANT: Your refrigerator has two adjustable, front leveling screws one on each side of the refrigerator base. If your refrigerator seems unsteady or you want the door to close easier, use the instructions below. • Before moving the refrigerator, raise the leveling screws so the front rollers are touching the floor. 1. Remove the base grille. Grasp the grille firmly and pull it toward you. REFRIGERATOR USE There are two refrigerator compartment doors. The doors can be opened and closed either separately or together. There is a vertically-hinged seal on the left refrigerator door. • When the left side door is opened, the hinged seal automatically folds inward so that it is out of the way. • When both doors are closed, the hinged seal automatically forms a seal between the two doors. A 2= Raise or lower the cabinet. Using a V4"hex driver, turn the leveling screw on each side to raise or lower that side of the refrigerator. NOTE: Having someone push against the top of the refrigerator takes some weight off the leveling screws. This makes it easier to turn the screws. It may take several turns of the leveling screw to adjust the tilt of the refrigerator. • To raise, turn the leveling screw clockwise. • To lower, turn the leveling screw counterclockwise. A. Hinged seal A. Leveling screw 3= Open the door again to make sure that it closes as easily as you like. If not, tilt the refrigerator slightly more to the rear by turning both leveling screws clockwise. It may take several more turns, and you should turn both screws the same amount. 4. Replace the base grille. The control center is located on the front of the ice and water dispenser. Temperature Controls For your convenience, your temperature controls are preset at the factory. When you first install your refrigerator, make sure the controls are still set to the recommended set points as shown. Recommended Settings IM PO RTANI"." • When the power is on, the temperature display shows the set point temperature of the compartment. • Wait 24 hours for your refrigerator to cool completely before adding food. If you add food before the refrigerator has cooled completely, your food may spoil. NOTE: Adjusting the refrigerator and freezer temperature controls to a colder than recommended setting will not cool the compartments any faster. 8

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40

IMPORTANT:
Your refrigerator
has two adjustable,
front
leveling screws
-
one on each side of the refrigerator
base. If your refrigerator
seems unsteady
or you want the door to close easier, use the
instructions
below.
Before moving
the refrigerator,
raise the leveling screws
so
the front rollers are touching
the floor.
1.
Remove
the base grille. Grasp the grille firmly
and pull it
toward
you.
2=
Raise or lower the cabinet.
Using a
V4"
hex driver, turn the leveling screw on each side to
raise or lower that side of the refrigerator.
NOTE: Having someone
push against the top of the
refrigerator
takes some weight
off the leveling screws.
This
makes it easier to turn the screws.
It may take several turns of
the leveling
screw to adjust the tilt of the refrigerator.
To raise, turn the leveling screw
clockwise.
To lower, turn the leveling screw
counterclockwise.
REFRIGERATOR
USE
There are two refrigerator
compartment
doors. The doors can be
opened
and closed
either separately
or together.
There is a vertically-hinged
seal on the left refrigerator
door.
When the left side door is opened,
the hinged seal
automatically
folds inward so that it is out of the way.
When both doors are closed,
the hinged seal automatically
forms a seal between the two doors.
A
A. Hinged seal
3=
A. Leveling
screw
Open the door again to make sure that it closes as easily as
you like. If not, tilt the refrigerator
slightly
more to the rear by
turning
both leveling screws
clockwise.
It may take several
more turns,
and you should
turn both screws
the same
amount.
4.
Replace the base grille.
The control
center is located
on the front
of the ice and water
dispenser.
Temperature
Controls
For your convenience,
your temperature
controls
are preset at
the factory. When you first install your refrigerator,
make sure the
controls
are still set to the recommended
set points as shown.
Recommended
Settings
IM PO RTANI"."
When the power is on, the temperature
display
shows the set
point temperature
of the compartment.
Wait 24 hours for your refrigerator
to cool completely
before
adding
food.
If you add food before the refrigerator
has
cooled
completely,
your food may spoil.
NOTE: Adjusting
the refrigerator
and freezer temperature
controls
to a colder than recommended
setting
will not cool
the compartments
any faster.
8