Maytag MHWE500VP Use and Care Guide - Page 23

To use washer

again:

1.

Flush water pipes. Reconnect water inlet hoses to faucets. Turn on both water faucets.

Electrical

Shock

Hazard

Plug

into

a grounded

3 prong

outlet.

Do

not

remove

ground

prong.

Do

not

use

an

adapter.

Do

not

use

an

extension

cord.

Failure

to

follow

these

instructions

can

result

in

death,

fire,

or

electrical

shock.

2.

Plug in washer

or reconnect

power.

3.

Run the

washer

through

the

Normal/Casual

cycle

with

I/2 the

manufacturer's

recommended

amount

of HE detergent

for

a medium-size

load,

to clean

the washer

and

remove

the antifreeze,

if used.

To

transport

the

washer:

1.

If washer

will

be moved

during

freezing

weather,

put

in 1 qt (1 I.) of R.V.-type

antifreeze

in the

drum.

Run washer

on

a Drain

& Spin

cycle.

2.

Unplug

the

power

cord.

3.

Disconnect

the

drain

hose from

the drain

system

and

attach

to rear

pane[

clips.

4.

Shut off

both

water

faucets.

5.

Disconnect

the water

inlet

hoses

from

faucets,

then

drain

the

hoses

and

clip

them

to the

rear pane[

of the washer.

IMPORTANT:

Ca[[

for service.

Do

not reuse

transport

bolts.

Washer

must

be transported

in the

upright

position.

To avoid

suspension

and

structural

damage

to your

washer,

it must

be

properly

set up for relocation

by a certified

technician.

Reinstalling

the

washer

1.

Follow

the

"Installation

Instructions"

to

locate,

[eve[,

and

connect

the washer.

2.

Run the

washer

through

the

Normal/Casual

cycle

with

% the

manufacturer's

recommended

amount

of HE detergent

for

a medium-size

load,

to clean

the washer

and

remove

the antifreeze,

if used.

TROUBLESHOOTING

First try the solutions

suggested here or visit our

website

and reference

FAQs (Frequently

Asked

Questions)

to possibly

avoid

the cost of

a

service call.

In the U.S.A.

www.maytag.com/help

In Canada

www.maytag.ca

Washer

displaying

code

message

and

tone

sounds

"F20"

(Water

Inlet

Problem--no

water

or insufficient

water

supply)

Select

POWER/CANCEl.

twice

to cancel

the

cycle.

Unplug

washer

or disconnect

power.

Check

the following:

Are

both

hot

and

cold

water

faucets

completely

turned

on?

Are

screens

at inlet

hose connection

to washer

clogged?

Are water

inlet

hoses

kinked?

Are water

inlet

hoses frozen?

Plug in washer

or reconnect

power.

Re-select

cycle

and

press START/PAUSE.

If the

problem

remains,

ca[[ for

service.

"F21"

(Drain

Problem)

Select

POWER/CANCEl.

twice

to

cancel

the

cycle.

Unplug

washer

or disconnect

power.

Check

the

following:

Is the drain

hose

kinked?

Is the

drain

hose frozen?

Is the drain

hose clogged?

Is the

drain

hose

more

than

96"

(2.4

m) above

the

floor?

Plug in washer

or reconnect

power.

Re-select

cycle

and

press START/PAUSE.

If the

problem

remains,

ca[[ for

service.

"SUD"

(Suds

Routine)

When

excessive

suds

are detected,

a suds

routine

automatically

starts. This routine

removes

extra

suds and

assures

proper

rinsing

of your

garments.

"SUI])"

is displayed

during

rinsing

and

at the end

of the

cycle

to

inform

you

that

Suds

Routine

was

activated.

Use only

HE (High

Efficiency)

detergents.

ii

.........

Maytag MHWE500VP Use and Care Guide - Page 23

Troubleshooting

Page 23 highlights