Maytag MVWB700VQ Use and Care Guide - Page 10
Excessive, Weight, Use two or more people to, washer., Failure to do so can result in back or other - year
 |
UPC - 883049140407
View all Maytag MVWB700VQ manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 10 highlights
Check for leaks I Turn on the water faucets and check for leaks. A small amount of water might enter the washer. YOu will drain this in a later step. NOTE: Replace inlet hoses after 5 years of use to reduce the risk of hose failure. Record hose installation or replacement dates for future reference. m [f you connect only one water hose, you must cap off the remaining water inlet port. m Periodically inspect and replace hoses if bulges, [
-
1 -
2
-
3
-
4
-
5 -
6 -
7 -
8 -
9 -
10 -
11 -
12 -
13 -
14 -
15 -
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
-
53
-
54
-
55
-
56
 |
 |
Check
for
leaks
I
Turn on
the water
faucets
and
check
for
leaks. A small
amount
of water
might
enter
the
washer.
YOu will
drain
this
in a later
step.
NOTE:
Replace
inlet
hoses
after
5 years of
use to reduce
the
risk of
hose failure.
Record
hose
installation
or replacement
dates
for future
reference.
m
[f you
connect
only
one
water
hose, you
must cap
off the
remaining
water
inlet
port.
m
Periodically
inspect
and
replace
hoses
if bulges,
[<inks, cuts,
wear,
or
leaks are found.
1.
2.
Drape
the
power
cord
over
the console.
Remove
any cardboard
used to
move
washer.
Beaded tie
.<rap
3.
Fasten the
drain
hose
to the
laundry
tub
leg or drain
standpipe
with
the
beaded
tie strap.
See view
A or B.
A
B
C
If the washer
faucets
and the
drain
standpipe
are recessed,
put
the
formed
end
of the
drain
hose
into
the standpipe.
Tightly
wrap
the
tie strap
around
the water
inlet
hoses
and the
drain
hose.
See view
C.
Excessive
Weight
Hazard
Use two or more people to
move
and
install
washer.
Failure to do so can result in back or other
injury.
1.
Slide
the washer
to
its final
location.
2.
Push on
upper
front
panel
to
be sure the washer
is on
its rear feet.
3.
I.ower
right
front
foot
until
it contacts
the floor.
By hand,
firmly
rotate
foot
as much
as an
additional
1
V2
turns.
The other
three
feet
have
been
preset
at the factory.
4.
Check
the
levelness
of the washer
by first
placing
a level
on the
lid near
the console.
level
the
#ont.
One
washer
foot
has been
installed
at a different
height
on your
new
washer.
The other
three feet
were
preset
at the factory.
Properly
leveling
your
washer
will
minimize
noise
and
vibration.
10