Maytag MVWB700VQ Use and Care Guide - Page 17

Rinse & Spin Use this option to get a deep rinse followed by a high-speed spin, The time display will include an estimate of how long it will take to fill and drain the washer. When to use RINSE & SPIN: [] For loads that need rinsing only. [] For completing a cycle after the cycle has been cancelled. Drain & Spin Drain & Spin may help shorten drying times for some heavy fabrics or special-care Drain & Spin may also be used for draining the washer after canceling a cycle. items. Modifiers allow you to further customize your cycles and save energy. modifiers I cold cold ! no spin m warm cold m warm warm a hot cold auto temperature control I wash temp I ! 10w L__L__J M medium m max I spin speed } extract ! light m medium m heavy/ L stains J Wash Temp/Rinse Temp Select a water temperature based on the type of load you are washing. water safe for fabrics. Follow garment [abe[ instructions. Use the warmest wash Warm rinses leave the loads drier and more comfortable to handle than cold rinses. However, warm rinses also increase wrinkling. Cold rinses may help with wrinkling and save energy. Wash Water Temperature Hot Warm Cold Suggested Fabrics Whites and pastels Bright colors Colors that bleed or fade NOTE: In wash water temperatures colder than 60°F (15.6°C), detergents do not dissolve we[[. Soils may be difficult to remove. Spin Speed This washer automatically selects the spin speed based on the cycle selected. The preset speeds can be changed. Spin speeds may vary by cycle. Soil Level Soil I_eve[ (wash time) is preset for each wash cycle. See "Preset Cycle Settings" in "Cycles." As you press the Soil Level pad, the cycle time wi[[ increase or decrease in the Estimated Time Remaining display and a different wash time wi[[ appear. To get the minimum wash time, press the pad until the indicator light next to I_ight illuminates. This is the shortest wash time available for that cycle with the wash options selected. [] For most loads, use the time recommended in the preset cycle settings. [] For heavy soil and sturdy fabrics, press Soil [.eve[ to select more wash time, if needed. [] For light soil and delicate fabrics, press Soil [.eve[ to select less wash time, if needed. Auto Temperature Control Auto Temperature Control (ATC) electronically senses and maintains a uniform wash and rinse water temperature. ATC regulates incoming hot and cold water. The ATC is automatically turned On when a cycle is selected. (See "Preset Cycle Settings" in "Cycles.") ATC is available with Warm/Warm, Warm/Cold, and Cool/Cold settings. The water temperature in the Hot/Cold and Cold/Cold settings depends on the water temperature water inlet faucets. at the [] ATC ensures consistent cleaning. [] Heated water consumes the largest amount of energy that a washer uses. [] Today's detergents work well at temperatures above 60°F (15.6°C). Use these pads to select or deselect the options for your wash cycle. Options may add time to the wash cycle. options iiiiiiiIii ii i! g ,saob.r.fi.tc. 1j REl oond,lsoigwn]ja,'h, ...!.i..... Water Save Spray Rinse The Water Save Spray Rinse option reduces rinse water in the cycle. This option is available on most cycles and must be selected prior to the start of the cycle. Do not use liquid fabric softener with the Water Save Spray Rinse option. Select the Fabric Softener option if using liquid fabric softener to assure proper dispensing. Fabric Softener Fabric Softener option must be selected if liquid fabric softener is added to the fabric softener dispenser. Fabric softener will also be dispensed in the last rinse of the Extra Rinse cycle, if selected. This option flushes the dispenser at the correct time in a deep water rinse for optimal distribution. Extra Rinse An Extra Rinse can be used to aid in the removal of detergent or bleach residue, or particulates such as sand and lint, from the load. This option provides an additional rinse with the same water temperature as the first rinse. This is the preset rinse setting for the Whites cycle. End Signal - Off - Low - Hi Cycle Volume The End Signal produces an audible sound when the wash cycle is finished. This signal is helpful when you are removing items from the washer as soon as it stops. Select Off, [.ow, or Hi for volume sound.