Maytag MVWB700VQ Use and Care Guide - Page 20

To use

washer again:

1.

Flush water

pipes

and

hoses,

Reconnect

water

inlet

hoses, Turn

on

both

water

faucets,

Electrical

Shock

Hazard

Plug

into

a grounded

3 prong

outlet.

Do

not

remove

ground

prong.

Do

not

use

an

adapter.

Do

not

use

an extension

cord.

Failure

to

follow

these

instructions

can

result

in death,

fire,

or

electrical

shock.

To transport

the

washer:

1.

Shut off both water faucets.

2.

Disconnect

and

drain

water

inlet

hoses.

3.

If the washer

will

be

moved

during

freezing

weather,

put

1 qt (1 [_)of

R.V.-type

antifreeze

in the

basket.

Run washer

on

the

Rinse

& Spin setting

for about

30 seconds

to

mix

the

antifreeze

and

remaining

water.

4.

Disconnect

the drain

from

the

drain

system.

5.

Unplug

the

power

cord.

6.

Place

the

inlet

hoses

into

the

basket.

7.

8.

Drape

the power

cord

and

drain

hose over

edge

into

the

basket.

Place

foam

packing

ring

from

the original

shipping

materials

in the

top

of washer,

if

you

do not

have the

original

foam

packing

ring,

place

heavy

blankets,

towels,

etc.

into

basket

opening.

Close

the

lid and

put

a piece

of tape

over

the

lid and

down

to the

front

of the

washer.

Keep

lid taped

until

the

washer

is placed

into

the

new

location.

Reinstalling

the

washer

1.

Follow

the

"Installation

Instructions"

to

locate,

[eve[,

and

connect

the washer.

2.

Run the

washer

through

the

Bulky

cycle

to clean

the

washer

and

remove

the

antifreeze,

if used.

Use only

HE

High

Efficiency

detergent.

Use % the

manufacturer's

recommended

amount

for a medium-size

load.

2.

3.

Plug in washer

or reconnect

power.

Run the washer

through

the

Bulky

cycle

to clean

the

washer

and

remove

the antifreeze,

if used.

Use only

HE High

Efficiency

detergent.

Use 1/2the

manufacturer's

recommended

amount

for a medium-size

load.

TROUBLESHOOTING

First try the

solutions

suggested

here

or visit

our

webslte

and

reference

FAQs (Frequently

Asked

Questions)

to possibly

avoid

the

cost

of a service

call

In U.S.A.

www.maytag.com/help

In Canada

www.maytag.ca

Washer

dlspiaying

code

messages

[]

LF

"LF"

(Washer

is taking

too

long

to fill)

Check

the

following:

Are

the hot

and

cold

faucets

turned

on?

Are

the water

inlet

hoses

[<inked

or clogged?

Are

the water

inlet

valve

screens

clear?

Press POWER/CANCEL

to clear

display.

[]

Ld

"Ld"

(Washer

is taking

too

long

to drain

water

from

the wash

tub)

Check

the

following:

Is the

drain

hose

kinked

or clogged?

Is the

drain

hose installed

properly?

See "Connect

the

Drain

Hose."

Press POWER/CANCEL

to clear

display.

[]

uL

"uL"

(Unbalanced

Load)

If the

load

is unbalanced,

the

washer

will

display

this

code

while

running

an imbalanced

load

correction

routine

at the

end

of the wash

cycle

and

before

the final

spin.

If the

code

remains

and the

wash

cycle

dial

is flashing

after the

recovery

routine

has stopped,

open

lid

and

redistribute

the

load.

Close

lid and

press START/PAUSE.

[]

_L

"oL"

(Over

Load)

Is the

washer

overloaded?

The washer

has attempted

to fill

and

begin

the

wash

cycle.

If

the

washer

is overloaded,

it will

drain

any water

and

detergent

that

was

added

during

the

fill.

To correct

the overload,

remove

several

items

and

add

detergent.

Close

lid and

press

START/PAUSE.

_d

"Sd"

(Suds

Detected)

Did

you

use

regular

detergent?

Regular

or non-HE

hand-washing

detergents

are not

recommended

for this

washer.

Use only

High

Efficiency

("HE")

detergent.

2O

Maytag MVWB700VQ Use and Care Guide - Page 20

Troubleshooting

Page 20 highlights