Memorex MVDP1077 User Guide - Page 37

Troubleshooting Guide

Get Memorex MVDP1077 PDF manuals and user guides View all Memorex MVDP1077 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 37 highlights

TROUBLESHOOTING GUIDE Check the following before requesting service: SYMPTOM GENERAL No power. Power on, but unit not functioning properly. POSSIBLE CAUSE Battery Pack is empty. Condensation has formed. Wrong type of disc inserted. Unit needs to be reset. POSSIBLE SOLUTION Recharge Battery Pack. Unplug the unit and wait about one to two hours to allow the player to dry. This unit cannot play discs, other than DVD, standard CDs or picture CDs. Turn the power off, then unplug the unit. Wait one minute and then plug the unit back in. No picture. The disc is dirty or inserted incorrectly. Some features and functions are not available on all discs. The equipment is not connected properly. The INPUT of the TV is not set to receive the DVD signal output. The video cables are not securely connected. Clean disc and insert label side-up. This is normal, try another function. Connect the equipment according to the instructions in this manual. Select the appropriate video input mode, usually VIDEO or AV. Connect the video cables securely. No sound. The equipment is not connected properly. The equipment connected with the audio cable is not set to receive the DVD signal input. The volume is turned all the way down. Connect the equipment according to the instructions in this manual. Select the appropriate audio input mode. Turn the volume up. Playback picture rolls. The playback picture is poor. The Search feature is not working. The picture is not fitting properly. The remote control is not working. The connected receiver's power is off. Unit needs to be reset to NTSC. The disc is dirty. Some discs have sections that do not allow searching. Wrong menu option is selected in the SETUP MENU. The battery is weak or dead. The battery is not installed properly. The remote is not aimed at the sensor. Distance is too far or there is too much light in the room. There is an obstacle in the path of the beam. Turn the audio receiver on. Select NTSC in the menus (see page 18). Clean the disc. This is normal on some discs. Select the correct TV type (PS, LB, 16:9) which matches the TV you are using. Install a fresh battery. Install battery according to the diagram. Aim the remote at the sensor. Operate within 20ft, or reduce the light in the room. Move obstacle. 36

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
Check the following before requesting service:
36
TROUBLESHOOTING GUIDE
SYMPTOM
GENERAL
No power.
Power on, but unit not functioning
properly.
No picture.
No sound.
Playback picture rolls.
The playback picture is poor.
The Search feature is not working.
The picture is not fitting properly.
The remote control is not working.
POSSIBLE SOLUTION
Recharge Battery Pack.
Unplug the unit and wait about one to
two hours to allow the player to dry.
This unit cannot play discs, other than
DVD, standard CDs or picture CDs.
Turn the power off, then unplug the unit.
Wait one minute and then plug the unit
back in.
Clean disc and insert label side-up.
This is normal, try another function.
Connect the equipment according to the
instructions in this manual.
Select the appropriate video input
mode, usually VIDEO or AV.
Connect the video cables securely.
Connect the equipment according to the
instructions in this manual.
Select the appropriate audio input
mode.
Turn the volume up.
Turn the audio receiver on.
Select NTSC in the menus (see page 18).
Clean the disc.
This is normal on some discs.
Select the correct TV type (PS, LB, 16:9)
which matches the TV you are using.
Install a fresh battery.
Install battery according to the diagram.
Aim the remote at the sensor.
Operate within 20ft, or reduce the light
in the room.
Move obstacle.
POSSIBLE CAUSE
Battery Pack is empty.
Condensation has formed.
Wrong type of disc inserted.
Unit needs to be reset.
The disc is dirty or inserted incorrectly.
Some features and functions are not
available on all discs.
The equipment is not connected properly.
The INPUT of the TV is not set to receive
the DVD signal output.
The video cables are not securely
connected.
The equipment is not connected properly.
The equipment connected with the audio
cable is not set to receive the DVD signal
input.
The volume is turned all the way down.
The connected receiver’s power is off.
Unit needs to be reset to NTSC.
The disc is dirty.
Some discs have sections that do not
allow searching.
Wrong menu option is selected in the
SETUP MENU.
The battery is weak or dead.
The battery is not installed properly.
The remote is not aimed at the sensor.
Distance is too far or there is too much
light in the room.
There is an obstacle in the path of the
beam.