Metabo KPA 18 LTX 400 Operating Instructions - Page 10
Accessories, Repairs, Environmental Protection, Technical Data
View all Metabo KPA 18 LTX 400 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 10 highlights
en ENGLISH - Now gently press the rod knob (8) to advance the toothed rod until it comes in contact with the cartridge. 7. Use 7.1 Multifunctional monitoring system If the device switches off automatically, the machine electronics have activated automatic protection mode. Causes and remedies: 1. Battery pack almost flat (the electronics prevent the battery pack from discharging totally and avoid irreparable damage). If the battery pack is almost flat, it must be recharged. 2. Long continuous overloading of the machine will activate the temperature cut-out. Leave the machine or battery pack to cool. 3. If the current is too high (for example, during extended periods of overloading) the device is switched off. Using the trigger switch, turn off the device (9) and remove the battery pack. Determine the cause of the problem and resolve it. 7.2 Setting the feed rate Set the feed rate using the adjusting wheel (10). 7.3 Switching on and off Switching on: press the trigger switch (9). Switching off: release the trigger switch (9). Note: The toothed rod is automatically retracted slightly to avoid dripping. However, if you activate the trigger switch at brief intervals (shorter than 1 second), the rod is not automatically retracted. This allows precise dosage of volumes. Note: The motor switches off automatically if either the cartridge or the plastic bag is empty. 8. Accessories Only use original Metabo battery packs and Metabo accessories. Use only accessories that fulfil the requirements and specifications listed in these operating instructions. Batter chargers: ASC Ultra, ASC 30-36, etc. Battery packs with different capacities. Buy battery packs only with voltage suitable for your power tool. Order no.: 6.25596 ....2.0 Ah Order no.: 6.25346 ...3.5 Ah etc. Conversion kit 400 ml Order no.: (315418210 + 343444950) Comprising a short toothed rod (7) and 400 ml tube (3) for replacing parts. 10 Conversion kit 600 ml Order no.: (315418070 + 343444960) Comprising a short toothed rod (7) and 600 ml tube (3) for replacing parts. Installation instructions for conversion kit: See page 2, fig. C. - Unscrew the tube (3). - Extract the screw from the rod knob (8) and pull the rod knob (8) back from the rod (7). - Pull the toothed rod forwards from the motor housing. - Extract the screw and dismantle the components (16) to (17) from the rod. - Insert the rod from the conversion kit towards the front. - Attach the rod knob (8) on top and fasten it in place with a screw. - Fit components (16) to (17) on the other rod and fasten in place with a screw. - Screw the tube from the conversion kit together tightly. For a complete range of accessories, see www.metabo.com or the catalogue. 9. Repairs Repairs to electrical tools must ONLY be carried out by qualified electricians! Contact your local Metabo representative if you have Metabo power tools requiring repairs. See www.metabo.com for addresses. You can download a list of spare parts from www.metabo.com. 10. Environmental Protection Observe national regulations on environmentally compatible disposal and on the recycling of disused tools, packaging and accessories. Battery packs may not be disposed of with regular waste. Return faulty or used battery packs to your Metabo dealer! Do not allow battery packs to come into contact with water! Only for EU countries: never dispose of power tools in your household waste! Used power tools must be collected separately and handed in for environmentally compatible recycling in accordance with European Directive 2002/96/EC on waste electrical and electronic equipment and its implementation in national legal systems. Discharge the battery pack in the power tool before disposal. Prevent the contacts from short-circuiting (e.g. by protecting them with adhesive tape). 11. Technical Data Explanatory notes on the specifications on page 3. Changes due to technological progress reserved. U = Voltage of battery pack v = Feed rate F = Extrusion force