Miele W 4842 Operating and Installation manual - Page 50

Installation site 46, Do not lift the washer by the drum

Get Miele W 4842 PDF manuals and user guides View all Miele W 4842 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 50 highlights

Installation Installation site For best performance front loading washers should be installed on the ground floor or basement of the building. A concrete or reinforced floor is the most suitable surface for the washer. These floors are less prone to vibration during the spin cycle. If the installation must be on a wooden joist floor: - the corner of a room where the stability of the floor is at its greatest is the best place to install the washer. ,The washer must not be built under a countertop. Installation ^ Use the front washer feet and the rear excess end to transport the washer from its shipping pallet to the installation site. Do not lift the washer by the drum door! ,Ensure that the machine's feet and the floor are dry to prevent slippage during the spin cycle. - the machine must be leveled and securely positioned. - to avoid vibration while spinning, the machine should not be installed on soft floor coverings. ^ Install the unit on a 1 1/4" (32 mm) thick, 28" x 31" (71x78 cm) wide plywood base. Ideally the base should be large enough to span several joists and should be anchored to the joists and not just the floor boards. ,If the machine is installed on a raised platform it must be secured with retaining clips available from your dealer or Miele. If installed on a masonry or concrete base, the base should have a ½" (13 mm) to ¾" (19 mm) high rim. This must be done to prevent the washer from vibrating off the stand during the spin cycle. 46

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
Installation site
For best performance front loading
washers should be installed on the
ground floor or basement of the
building.
A concrete or reinforced floor is the
most suitable surface for the washer.
These floors are less prone to vibration
during the spin cycle.
If the installation must be on a wooden
joist floor:
– the corner of a room where the
stability of the floor is at its greatest is
the best place to install the washer.
– the machine must be leveled and
securely positioned.
– to avoid vibration while spinning, the
machine should not be installed on
soft floor coverings.
^
Install the unit on a 1
1
/
4
" (32 mm)
thick, 28" x 31" (71x78 cm) wide
plywood base. Ideally the base
should be large enough to span
several joists and should be
anchored to the joists and not just the
floor boards.
,
If the machine is installed on a
raised platform it must be secured
with retaining clips available from
your dealer or Miele.
If installed on a masonry or concrete
base, the base should have a ½"
(13 mm) to ¾" (19 mm) high rim.
This must be done to prevent the
washer from vibrating off the stand
during the spin cycle.
,
The washer must not be built
under a countertop.
Installation
^
Use the front washer feet and the
rear excess end to transport the
washer from its shipping pallet to the
installation site.
Do not lift the washer by the drum
door!
,
Ensure that the machine’s feet
and the floor are dry to prevent
slippage during the spin cycle.
Installation
46