NaceCare ETB1120 ETB1120 Owners Manual - Page 17

ETB 1120, Trouble Shooting

Page 17 highlights

PROBLEM Machine will not operate Vacuum will not operate Poor water pick-up No brush / scrub function Little or no water flow Machine just 'stops' while operating Trouble Shooting CAUSE Missing or blown fuses Battery not connected Low battery charge Vacuum not turned on Waste-water tank full Clogged / blocked vacuum hose Loose hose connections Debris basket filter clogged/blocked Separator filter clogged / blocked Poor separator seal Damaged separator seal Damaged / split vacuum hose Damaged floor-tool blades Low battery charge No brushes fitted Brush overloaded Clean-water tank empty Clean-water tank filter blocked/ clogged Clean water tap not turned on Too much load on the brush system Blown fuse SOLUTION Fit or replace fuse Connect battery Charge batteries (page 16) Turn on vacuum (page 13) Empty waste-water tank (page 14) Remove and clean (page 14) Push tight connections (page 14) Remove and clean (page 14) Remove and clean (page 14) Clean and refit (page 14) Renew (contact service dept) Renew (contact service dept) Renew (contact service dept) Recharge batteries Check and fit (page 10) Reset machine (page 13) Fill clean-water tank (page 11) Remove and clean (page 14) Turn on clean water tap (page 9) Reset the machine and decrease the brush load to best suit the floor type (page 13) Replace fuse Brush Motor 400W Vac Motor 400W Brush Sizes 20'' Pad sizes 20'' Weight 335 lbs Protection Class IPX4 ETB 1120 Power 2 x 12V (24V) 100Ah Fluid Flow Speed Cleaning Speed Hand Arm Vibration Noise Size 0.53 gpm 100 rpm 0 - 0.31mph 577877 577878 577839 206265 207000 206698 213047 303641 606309 606028 606550 606037 Top Tank - Red Bottom Tank - Red Separator Barrel Filter Basket Filter Floor Tool Hose Dump Hose Top Dump Hose Bottom Floor Tool Polyscrub Brush 20" Nyloscrub Brush 20" Recommended floor tool Blade Set 0.57 m/s2 Hi-69 dB(A) Lo-67 dB(A) Width - 22'' Length - 40.5'' Height - 45.6'' 208638 577812 577892 321686 208588 221107 206813 229295 206953 606551 606403 606071 Wheel Deck Handle Vac Motor Vac Hose 50 Amp Fuse (Batteries) Isolator Pin \ Key Floor Tool Retaining Pin Detent Pin Long Life Brush 20" Padloc Drive Board 20" Replacment Polyurethane Blade Set (optional) 17

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32

17
577877
Top Tank - Red
208638
Wheel
577878
Bottom Tank - Red
577812
Deck
577839
Separator
577892
Handle
206265
Barrel Filter
321686
Vac Motor
207000
Basket Filter
208588
Vac Hose
206698
Floor Tool Hose
221107
50 Amp Fuse (Batteries)
213047
Dump Hose Top
206813
Isolator Pin \ Key
303641
Dump Hose Bottom
229295
Floor Tool Retaining Pin
606309
Floor Tool
206953
Detent Pin
606028
Polyscrub Brush 20”
606551
Long Life Brush 20”
606550
Nyloscrub Brush 20”
606403
Padloc Drive Board 20”
606037
Recommended floor tool Blade Set
606071
Replacment Polyurethane Blade Set (optional)
ETB 1120
Brush Motor
Vac Motor
Brush Sizes
Pad
sizes
Weight
Protection
Class
Power
400W
400W
20’’
20’’
335 lbs
IPX4
2 x 12V (24V) 100Ah
Fluid Flow
Speed
Cleaning Speed
Hand Arm Vibration
Noise
Size
0.53 gpm
100 rpm
0 - 0.31mph
0.57 m/s
2
Hi-69 dB(A)
Lo-67 dB(A)
Width - 22’’
Length - 40.5’’
Height - 45.6’’
PROBLEM
CAUSE
SOLUTION
Machine will not operate
Missing or blown fuses
Battery not connected
Low battery charge
Fit or replace fuse
Connect battery
Charge batteries (page 16)
Vacuum will not operate
Vacuum not turned on
Turn on vacuum (page 13)
Poor water pick-up
Waste-water tank full
Clogged / blocked vacuum hose
Loose hose connections
Debris basket filter clogged/blocked
Separator filter clogged / blocked
Poor separator seal
Damaged separator seal
Damaged / split vacuum hose
Damaged floor-tool blades
Low battery charge
Empty waste-water tank (page 14)
Remove and clean (page 14)
Push tight connections (page 14)
Remove and clean (page 14)
Remove and clean (page 14)
Clean and refit (page 14)
Renew (contact service dept)
Renew (contact service dept)
Renew (contact service dept)
Recharge batteries
No brush / scrub function
No brushes fitted
Brush overloaded
Check and fit (page 10)
Reset machine (page 13)
Little or no water flow
Clean-water tank empty
Clean-water tank filter blocked/ clogged
Clean water tap not turned on
Fill clean-water tank (page 11)
Remove and clean (page 14)
Turn on clean water tap (page 9)
Machine just ‘stops’ while
operating
Too much load on the brush system
Blown fuse
Reset the machine and decrease the
brush load to best suit the floor type
(page 13)
Replace fuse
Trouble Shooting