Netgear GS308E Gigabit Ethernet Smart Managed Plus Switches User Manual - Page 76

Factory Default Settings - factory reset

Get Netgear GS308E PDF manuals and user guides View all Netgear GS308E manuals
Add to My Manuals
Save this manual to your list of manuals

Page 76 highlights

Gigabit Ethernet Smart Managed Plus Switches Factory Default Settings You can return the switch to its factory settings. Use the end of a paper clip or some other similar object to press and hold the Factory Defaults button on the front panel of the switch for at least two seconds. The switch resets and returns to the factory settings that are shown in the following table. Table 9. Factory default settings Feature Switch password IP address Subnet mask DHCP mode IGMP snooping LAGs VLANs 802.1p/DSCP-based QoS Port-based QoS Rate limiting Broadcast filtering Loop detection Port speed Flow control Port mirroring Setting password 192.168.0.239 (if the switch is not connected to a network with a DHCP server) 255.255.255.0 Enabled Enabled None configured Disabled. If enabled, by default, all ports are members of VLAN 1. Enabled Disabled Disabled Disabled Disabled Autonegotiation Disabled Disabled Factory Default Settings and 76 Technical Specifications User Manual

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
Factory Default Settings
You can return the switch to its factory settings. Use the end of a paper clip or some
other similar object to press and hold the
Factory Defaults
button on the front panel
of the switch for at least two seconds. The switch resets and returns to the factory settings
that are shown in the following table.
Table 9. Factory default settings
Setting
Feature
password
Switch password
192.168.0.239 (if the switch is not connected to a network with a DHCP server)
IP address
255.255.255.0
Subnet mask
Enabled
DHCP mode
Enabled
IGMP snooping
None configured
LAGs
Disabled. If enabled, by default, all ports are members of VLAN 1.
VLANs
Enabled
802.1p/DSCP-based QoS
Disabled
Port-based QoS
Disabled
Rate limiting
Disabled
Broadcast filtering
Disabled
Loop detection
Autonegotiation
Port speed
Disabled
Flow control
Disabled
Port mirroring
User Manual
76
Factory Default Settings and
Technical Specifications
Gigabit Ethernet Smart Managed Plus Switches