Nokia CK 300 User Guide - Page 31

Hands-free unit HF-21W, hands-free unit and a metal surface is over 4 mm 0.16 inch. - bluetooth car kit hands free

Get Nokia CK 300 - Bluetooth hands-free Car PDF manuals and user guides View all Nokia CK 300 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 31 highlights

Installation Hands-free unit HF-21W The hands-free unit has the following connectors. The symbols are printed at the bottom of the unit. -Power -Loudspeaker output for phone calls; for connections, see "Integration with a car stereo system," p. 23 -System connector for connectivity cable CA-113CU to charge a mobile device and play music over a cable connection -Connector for the input device CU-10 -Stereo music output -Connector for the microphone MP-2 When you install the hands-free unit, ensure that the cables for the microphone and loudspeaker reach the places where you intend to mount these parts. Do not mount the hands-free unit inside a metal housing or on a metal surface because this will impair the Bluetooth connection between the hands-free unit and the Bluetooth device that is connected to the car kit. For an optimal connection, ensure that the distance between the hands-free unit and a metal surface is over 4 mm (0.16 inch). To mount the hands-free unit, use the hook and loop tape pads supplied with the car kit. Do as follows: 1. Detach the two pads from each other. 2. Attach the pad with the loops: peel off the protective sheet from the adhesive side, and attach the pad to the desired location in the car. When you peel off the protective sheet, do not touch the adhesive side with a finger. Ensure that the surface where you attach the pad is dry and free from dirt and dust. 31

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
Installation
31
Hands-free unit HF-21W
The hands-free unit has the following connectors. The symbols are
printed at the bottom of the unit.
—Power
—Loudspeaker output for phone calls; for connections, see
“Integration with a car stereo system,” p. 23
—System connector for connectivity cable CA-113CU to charge a
mobile device and play music over a cable connection
—Connector for the input device CU-10
—Stereo music output
—Connector for the microphone MP-2
When you install the hands-free unit, ensure that the cables for the
microphone and loudspeaker reach the places where you intend to
mount these parts.
Do not mount the hands-free unit inside a metal housing or on a metal
surface because this will impair the Bluetooth connection between the
hands-free unit and the Bluetooth device that is connected to the car
kit. For an optimal connection, ensure that the distance between the
hands-free unit and a metal surface is over 4 mm (0.16 inch).
To mount the hands-free unit, use the hook and loop tape pads supplied
with the car kit. Do as follows:
1.
Detach the two pads from each other.
2.
Attach the pad with the loops: peel off the protective sheet from the
adhesive side, and attach the pad to the desired location in the car.
When you peel off the protective sheet, do not touch the adhesive
side with a finger. Ensure that the surface where you attach the pad
is dry and free from dirt and dust.