NordicTrack E11.0 Elliptical English Manual - Page 23

Maintenance And Troubleshooting

Get NordicTrack E11.0 Elliptical PDF manuals and user guides View all NordicTrack E11.0 Elliptical manuals
Add to My Manuals
Save this manual to your list of manuals

Page 23 highlights

MAINTENANCE AND TROUBLESHOOTING Inspect and tighten all parts of the elliptical regularly. Replace any worn parts immediately. To clean the elliptical, use a damp cloth and a small amount of mild soap. IMPORTANT: To avoid damage to the console, keep liquids away from the console and keep the console out of direct sunlight. Next, look into the access opening and locate the Reed Switch (69). Rotate the Large Pulley (74) until a Pulley Magnet (75) is aligned with the Reed Switch. CONSOLE TROUBLESHOOTING If the console does not turn on, make sure that the power cord is fully plugged in. If lines appear in the console display, see HOW TO CHANGE CONSOLE SETTINGS on page 22 and adjust the contrast level of the display. If the handgrip pulse sensor does not function prop- erly, see step 5 on page 18. 106 75 74 HOW TO CALIBRATE THE RAMP 69 If the ramp is not functioning properly, the ramp may need to be calibrated. To calibrate the ramp, press and hold the Calories button for several seconds until the test mode appears in the display. Press the Calories button again. Then, press the Power Adjustable Ramp increase or decrease button to calibrate the ramp. The ramp will move upward and downward as it calibrates. Next, loosen, but do not remove, the indicated M4 x 16mm Screw (106). Slide the Reed Switch (69) slightly toward or away from the Pulley Magnet (75). Then, retighten the Screw. When the ramp stops moving, the ramp is calibrated. Then, press the Calories button repeatedly to exit the calibration mode. HOW TO ADJUST THE REED SWITCH Plug in the power cord and rotate the large pulley for a moment. Repeat these actions until the console displays correct feedback. When the reed switch is correctly adjusted, reattach the access cover. If the console does not display correct feedback, the reed switch should be adjusted. To adjust the reed switch, first unplug the power cord. Using a flat screw- 20 driver, release the tabs on the Access Cover (20) and pry the Access Cover upward off the ellip- tical. 23

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
23
Inspect and tighten all parts of the elliptical regularly.
Replace any worn parts immediately.
To clean the elliptical, use a damp cloth and a small
amount of mild soap.
IMPORTANT: To avoid damage
to the console, keep liquids away from the con-
sole and keep the console out of direct sunlight.
CONSOLE TROUBLESHOOTING
If the console does not turn on, make sure that the
power cord is fully plugged in. If lines appear in the
console display, see HOW TO CHANGE CONSOLE
SETTINGS on page 22 and adjust the contrast level of
the display.
If the handgrip pulse sensor does not function prop-
erly, see step 5 on page 18.
HOW TO CALIBRATE THE RAMP
If the ramp is not functioning properly, the ramp may
need to be calibrated. To calibrate the ramp, press
and hold the Calories button for several seconds until
the test mode appears in the display.
Press the Calories button again. Then, press the
Power Adjustable Ramp increase or decrease button
to calibrate the ramp. The ramp will move upward and
downward as it calibrates.
When the ramp stops moving, the ramp is calibrated.
Then, press the Calories button repeatedly to exit the
calibration mode.
HOW TO ADJUST THE REED SWITCH
If the console does not display correct feedback, the
reed switch should be adjusted.
To adjust the reed
switch, first unplug
the power cord.
Using a flat screw-
driver, release the
tabs on the Access
Cover (20) and pry
the Access Cover
upward off the ellip-
tical.
Next, look into the access opening and locate the
Reed Switch (69). Rotate the Large Pulley (74) until a
Pulley Magnet (75) is aligned with the Reed Switch.
Next, loosen, but do not remove, the indicated M4 x
16mm Screw (106). Slide the Reed Switch (69)
slightly toward or away from the Pulley Magnet (75).
Then, retighten the Screw.
Plug in the power cord and rotate the large pulley for a
moment. Repeat these actions until the console dis-
plays correct feedback. When the reed switch is
correctly adjusted, reattach the access cover.
MAINTENANCE AND TROUBLESHOOTING
20
106
75
69
74