Oki ML621 ML620, ML621 Users' Guide - English - Page 20

tractor cover., then close

Get Oki ML621 PDF manuals and user guides View all Oki ML621 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 20 highlights

. Make sure the tractor assembly is in the front of the printer. If the tractor is in the back, remove the sheet guide, grab the finger guides (1) on each side and pinch them together to release the guide. Remove it from the back and insert it into the front feed and when it is seated, push down to snap the guides in place. Replace the back sheet guide. 1 1 . Pull up on the lock levers to release them. . You will find reference marks on the printer for the most common paper sizes. . Move the left tractor to the position to match your paper size and push back on the lever to lock it in place, then move the right tractor to fit the width of the paper. . Open the tractor covers and place continuous forms paper on the first two pins of either tractor, then close the left tractor cover. Important! You must keep the number of paper holes engaged on either pin the same. If you don't the paper will skew and jam. . Adjust the position of the right tractor to center the holes in the paper on the pins. Then, close the tractor cover and push back the lock lever. Do not stretch the paper. Note: If the paper is too loose or too tight it can cause jams. . Press and hold the LOAD/EJECT key to advance the paper. Note: The factory default setting for the Top of Form (where the printing should begin) is 11/12" (23.28 mm) down from the top of the page. To change the setting, see "Top of Form (TOF)". ML620/ML621 User's Guide 20

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
ML620/ML621 User’s Guide
±0
Make sure the tractor assembly is in the front of
the printer. If the tractor is in the back, remove
the sheet guide, grab the finger guides (1) on
each side and pinch them together to release the
guide. Remove it from the back and insert it into
the front feed and when it is seated, push down
to snap the guides in place. Replace the back
sheet guide.
Pull up on the lock levers to release them.
You will find reference marks on the printer for
the most common paper sizes.
Move the left tractor to the position to match
your paper size and push back on the lever to
lock it in place, then move the right tractor to fit
the width of the paper.
Open the tractor covers and place continuous
forms paper on the first two pins of either tractor,
then close the
left
tractor cover.
².
³.
´.
µ.
¶.
Important!
You must keep the number of paper holes engaged on
either pin the same. If you don’t the paper will skew
and jam.
Adjust the position of the right tractor to center
the holes in the paper on the pins. Then, close
the tractor cover and push back the lock lever. Do
not stretch the paper.
Note: If the paper is too loose or too tight it can cause
jams.
Press and hold the
LOAD/EJECT
key to advance
the paper.
Note: The factory default setting for the Top of Form
(where the printing should begin) is 11/12”
(23.28 mm) down from the top of the page. To
change the setting, see “Top of Form (TOF)”.
·.
¸.
1
1