Oki ML6300 User Guide - Page 48

Esponding, General, Problems

Get Oki ML6300 PDF manuals and user guides View all Oki ML6300 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 48 highlights

RESPONDING TO GENERAL PROBLEMS Use the following table to help you to identify symptoms with possible causes and take suggested remedial actions. PROBLEM CAUSE ACTION No power No power The power cable is not properly connected. Power outlet problem or power outage. No printing takes place SEL indicator is unlit. The printer driver is not installed properly. The printer has just stopped printing. There is no paper in the printer. SEL indicator is illuminated but no printing takes place. Inrterface cable is disconnected. Wrong interface cable has been used. The print head is moving but no printing takes place. The ribbon cartridge has not been installed. Print position offset The horizontal printing position is offset. The start position may change after the printer is powered on. Check the power cable is properly connected at both power outlet and printer. Plug another appliance into this outlet to check if it works. Re-install the printer driver correctly. Press the SEL button. Load paper. Reconnect the interface cable. Use correct interface cable. Install the ribbon cartridge. When the printer is powered ON, switch from off-line mode to on-line mode by pressing the SEL button. Reset the start position. You must set the Power Switch to OFF before you change the start position. Troubleshooting > 48

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
Troubleshooting > 48
R
ESPONDING
TO
GENERAL
PROBLEMS
Use the following table to help you to identify symptoms with
possible causes and take suggested remedial actions.
PROBLEM
CAUSE
ACTION
No power
No power
The power cable is not
properly connected.
Check the power cable
is properly connected at
both power outlet and
printer.
Power outlet problem or
power outage.
Plug another appliance
into this outlet to check
if it works.
No printing takes place
SEL indicator is unlit.
The printer driver is not
installed properly.
Re-install the printer
driver correctly.
The printer has just
stopped printing.
Press the SEL button.
There is no paper in the
printer.
Load paper.
SEL indicator is
illuminated but no
printing takes place.
Inrterface cable is
disconnected.
Reconnect the interface
cable.
Wrong interface cable
has been used.
Use correct interface
cable.
The print head is
moving but no printing
takes place.
The ribbon cartridge
has not been installed.
Install the ribbon
cartridge.
Print position offset
The horizontal printing
position is offset.
The start position may
change after the printer
is powered on.
When the printer is
powered ON, switch
from off-line mode to
on-line mode by
pressing the SEL
button. Reset the start
position. You must set
the Power Switch to OFF
before you change the
start position.