Olympus D595 D-595 Zoom Advanced Manual (English) - Page 125

Set [ALL RESET] to [OFF]., See Error codes.

Get Olympus D595 - 5MP Digital Camera PDF manuals and user guides
UPC - 050332153332
View all Olympus D595 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 125 highlights

Troubleshooting Possible cause Corrective action Ref. page There is a problem with See "Error codes". the card. P. 122 The monitor does not turn on. The camera is set to [MONITOR OFF]. Press Z in the shooting mode to display the top menu, then press c to select [MONITOR ON]. P. 24 The viewfinder or monitor is hard to see. There is condensation* inside the camera. The brightness of the monitor is not adjusted properly. Turn the camera off and wait until it dries before turning it on again. Use [s] to adjust monitor brightness. - P. 89 The monitor is exposed Block the sunlight with your hand or use the - to direct sunlight. viewfinder while taking pictures. Vertical lines appear on Aiming the camera at a bright subject in - the monitor screen sunlight may cause vertical lines to appear during shooting. on the screen. This is not a malfunction. The date recorded with the image data is wrong. The date/time is not set. Set the date/time. The clock adjustment is not factory-preset. P. 90 The camera has been left without batteries. If the camera is left without batteries for 3 days, the date/time setting is canceled. Set the date/time again. P. 90 The settings are returned to the factory default settings when the camera is turned off. [ALL RESET] is set to [ON]. Set [ALL RESET] to [OFF]. P. 81 The picture is out of focus. The subject was too close. Auto focus is not possible. Move further away from the subject. To take P. 41 pictures closer than 20 cm (7.9") with the zoom in the maximum wide position, use the super macro mode. 9 Use the focus lock to focus on your subject. P. 25 There is condensation* Turn the camera off and wait until it dries - on the lens. before turning it on again. Appendix 125

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
Troubleshooting
125
9
Appendix
There is a problem with
the card.
See “Error codes”.
P. 122
The monitor does not turn on.
The camera is set to
[MONITOR OFF].
Press
Z
in the shooting mode to display the
top menu, then press
c
to select
[MONITOR ON].
P. 24
The viewfinder or monitor is hard to see.
There is condensation*
inside the camera.
Turn the camera off and wait until it dries
before turning it on again.
–
The brightness of the
monitor is not adjusted
properly.
Use [
s
] to adjust monitor brightness.
P. 89
The monitor is exposed
to direct sunlight.
Block the sunlight with your hand or use the
viewfinder while taking pictures.
–
Vertical lines appear on
the monitor screen
during shooting.
Aiming the camera at a bright subject in
sunlight may cause vertical lines to appear
on the screen. This is not a malfunction.
–
The date recorded with the image data is wrong.
The date/time is not set.
Set the date/time. The clock adjustment is
not factory-preset.
P. 90
The camera has been
left without batteries.
If the camera is left without batteries for 3
days, the date/time setting is canceled. Set
the date/time again.
P. 90
The settings are returned to the factory default settings when the camera is turned
off.
[ALL RESET] is set to [ON].
Set [ALL RESET] to [OFF].
P. 81
The picture is out of focus.
The subject was too
close.
Move further away from the subject. To take
pictures closer than 20 cm (7.9") with the
zoom in the maximum wide position, use the
super macro mode.
P. 41
Auto focus is not
possible.
Use the focus lock to focus on your subject.
P. 25
There is condensation*
on the lens.
Turn the camera off and wait until it dries
before turning it on again.
–
Possible cause
Corrective action
Ref.
page