Onkyo HT-S6500 Owner Manual - Page 31

En-31, Audyssey 2EQ Full Calibration, and then press - review

Get Onkyo HT-S6500 PDF manuals and user guides View all Onkyo HT-S6500 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 31 highlights

1 Turn on the AV receiver and the connected TV. On the TV, select the input to which the AV receiver is connected. Note • Before plugging the Speaker setup microphone to perform Automatic Speaker Setup, please make sure that all your connected speakers and subwoofers produce sound. 2 Set the speaker setup microphone at the Main Listening Position B, and connect it to the SETUP MIC jack. SETUP MIC jack Speaker setup microphone Note • The on-screen menus appear only on a TV that is connected to HDMI OUT. If your TV is connected to other video outputs, use the AV receiver's display when changing settings. 3 Use R/X to select "Audyssey Quick Start" or "Audyssey 2EQ Full Calibration", and then press ENTER. 4 Press ENTER. Audyssey 2EQ® Room Correction and Speaker Setup starts. Test tones are played through each speaker as Audyssey 2EQ Room Correction and Speaker Setup runs. This process takes a few minutes. Please refrain from talking during measurements and do not stand between speakers and the microphone. Do not disconnect the speaker setup microphone during Audyssey 2EQ Room Correction and Speaker Setup, unless you want to cancel the setup. If you select "Audyssey Quick Start", you will go to step 7. 5 Place the speaker setup microphone at the next position, and then press ENTER. Audyssey 2EQ performs more measurements. This takes a few minutes. 6 When prompted, repeat step 5. Turning On & Basic Operations 7 Use R/X to select an option, and then press ENTER. 2EQ Auto Setup Audyssey Subwoofer Front Center Surround Crossover : Yes : Small : Small : Small : 100Hz Save Cancel The options are: ` Save: Save the calculated settings and exit Audyssey 2EQ Room Correction and Speaker Setup. ` Cancel: Cancel Audyssey 2EQ Room Correction and Speaker Setup. Tip • You can view the calculated settings for the speaker configuration, speaker distances, and speaker levels by using F/S. 8 Use R/X to select a target, and use F/S to change the setting. After the results of Audyssey 2EQ have been saved, the menu will display the "Audyssey" (➔ page 42), "Dynamic EQ" (➔ page 42), "Dynamic Volume" (➔ page 42) settings. Note • When "Audyssey Quick Start" has been used for measurement, "Audyssey" cannot be selected. • These settings are applied to all input selectors. 9 Press ENTER. 10 Disconnect the speaker setup microphone. En-31

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
Turning On & Basic Operations
En-31
1
Turn on the AV receiver and the connected TV.
On the TV, select the input to which the AV receiver
is connected.
Note
•
Before plugging the Speaker setup microphone to perform
Automatic Speaker Setup, please make sure that all your
connected speakers and subwoofers produce sound.
2
Set the speaker setup microphone at the Main
Listening Position
a
, and connect it to the
SETUP
MIC
jack.
Note
•
The on-screen menus appear only on a TV that is connected
to
HDMI OUT
. If your TV is connected to other video
outputs, use the AV receiver’s display when changing
settings.
3
Use
q
/
w
to select “Audyssey Quick Start” or
“Audyssey 2EQ Full Calibration”, and then press
ENTER
.
Speaker setup microphone
SETUP MIC
jack
4
Press
ENTER
.
Audyssey 2EQ
®
Room Correction and Speaker Setup
starts.
Test tones are played through each speaker as
Audyssey 2EQ Room Correction and Speaker Setup
runs. This process takes a few minutes. Please
refrain
from talking
during measurements and
do not stand
between speakers and the microphone.
Do not disconnect the speaker setup microphone
during Audyssey 2EQ Room Correction and Speaker
Setup, unless you want to cancel the setup.
If you select “
Audyssey Quick Start
”, you will go to
step 7.
5
Place the speaker setup microphone at the next
position, and then press
ENTER
.
Audyssey 2EQ performs more measurements. This
takes a few minutes.
6
When prompted, repeat step 5.
7
Use
q
/
w
to select an option, and then press
ENTER
.
The options are:
Save
:
Save the calculated settings and exit
Audyssey 2EQ Room Correction and Speaker
Setup.
Cancel
:
Cancel Audyssey 2EQ Room Correction and
Speaker Setup.
Tip
•
You can view the calculated settings for the speaker
configuration, speaker distances, and speaker levels by
using
e
/
r
.
8
Use
q
/
w
to select a target, and use
e
/
r
to change
the setting.
After the results of Audyssey 2EQ have been saved,
the menu will display the “Audyssey” (
➔
page 42
),
“Dynamic EQ” (
➔
page 42
), “Dynamic Volume”
(
➔
page 42
) settings.
Note
• When “
Audyssey Quick Start
” has been used for
measurement, “
Audyssey
” cannot be selected.
•
These settings are applied to all input selectors.
9
Press
ENTER
.
10
Disconnect the speaker setup microphone.
Subwoofer
:
Yes
Front
:
Small
Center
:
Small
Surround
:
Small
Crossover
:
100Hz
Save
Cancel
2EQ Auto Setup
Audyssey
<- Review Speaker Configuration ->