Onkyo TX-NR5007 Owner Manual - Page 95

Speaker Setup, Full Band, 40Hz, 80HzTHX default, 100Hz

Get Onkyo TX-NR5007 - AV Network Receiver PDF manuals and user guides
UPC - 751398008849
View all Onkyo TX-NR5007 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 95 highlights

Advanced Setup-Continued Speaker Setup Some of the settings in this section are set automatically by Audyssey MultEQ® XT Room Correction and Speaker Setup (see page 61). For Speakers B, you need to change the settings manually. Here you can check the settings made by Audyssey MultEQ® XT Room Correction and Speaker Setup, or set them manually, which is useful if you change one of the connected speakers after using Audyssey MultEQ® XT Room Correction and Speaker Setup. Note: The Speaker Setup cannot be carried out while headphones are connected to the AV receiver. 1 Press the [RECEIVER] button, and then use the remote controller's [SP LAYOUT] button to select Speakers A or Speakers B. Note: Speakers B cannot be selected if "Speakers Type(FrontB)" is set to "Not Use". 2 Press the [SETUP] button. The main menu appears onscreen. If the main menu doesn't appear, make sure the appropriate external input is selected on your TV. 3 Use the Up and Down [R]/[X] buttons to select "2. Speaker Setup", and then press [ENTER]. 4 Use the Up and Down [R]/[X] buttons to select the submenu, and then press [ENTER]. 5 Use the Up and Down [R]/[X] buttons to select setting, and then use the Left and Right [F]/[S] buttons to set them. 6 When you've finished, press the [SETUP] button. The setup menu closes. Speaker Settings See "Speaker Settings" on page 57. Speaker Configuration With these settings, you can specify which speakers are connected and a crossover frequency for each speaker. You can set the crossover frequencies, distances, and levels of the front Speakers A and front Speakers B independently. The other speakers (i.e., subwoofer, center, surround, and surround back) use the same crossover frequencies, distances, and levels for Speakers A and Speakers B. The following crossover frequencies can be specified: "Full Band", "40Hz", "50Hz", "60Hz", "70Hz", "80Hz(THX)", "90Hz", "100Hz", "120Hz", "150Hz", or "200Hz". Specify "Full Band" for speakers that can output low frequency bass sounds adequately, for example, speakers with a good sized woofer. For smaller speakers, specify a crossover frequency. Sounds below the crossover frequency will be output by the subwoofer instead of the speaker. Refer to your speaker's manuals to determine the optimum crossover frequencies. If you set up your speakers using Audyssey MultEQ® XT Room Correction and Speaker Setup, please make sure manually that any THX speakers are set to "80Hz(THX)" crossover. Subwoofer 1ch: Audio signal is outputted from SW1 jack only. 2ch: Audio signal is outputted from SW1 and SW2 jacks (default). No: Select if no subwoofer is connected. Front*1 Full Band, 40Hz, 50Hz, 60Hz, 70Hz, 80Hz(THX) (default), 90Hz, 100Hz, 120Hz, 150Hz, 200Hz Center*2 Surround*2 Front Wide*2*3*5*7 Front High*2*3*7*10 Surr Back*3*4*6 Full Band, 40Hz, 50Hz, 60Hz, 70Hz, 80Hz(THX), 90Hz, 100Hz, 120Hz, 150Hz, 200Hz None: Select if no speaker is connected. 95

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
95
Advanced Setup
—Continued
Some of the settings in this section are set automatically by Audyssey MultEQ
®
XT Room Correction and Speaker
Setup (see page 61). For Speakers B, you need to change the settings manually.
Here you can check the settings made by Audyssey MultEQ
®
XT Room Correction and Speaker Setup, or set them
manually, which is useful if you change one of the connected speakers after using Audyssey MultEQ
®
XT Room Cor-
rection and Speaker Setup.
Note:
The Speaker Setup cannot be carried out while headphones are connected to the AV receiver.
Speaker Setup
1
Press the [RECEIVER] button, and then
use the remote controller’s [SP LAYOUT]
button to select Speakers A or
Speakers B.
Note:
Speakers B cannot be selected if “Speakers
Type(FrontB)” is set to “Not Use”.
2
Press the [SETUP] button.
The main menu appears onscreen.
If the main menu doesn’t appear, make sure the
appropriate external input is selected on your TV.
3
Use the Up and Down [
q
]/[
w
] buttons to
select “2. Speaker Setup”, and then press
[ENTER].
4
Use the Up and Down [
q
]/[
w
] buttons to
select the submenu, and then press
[ENTER].
5
Use the Up and Down [
q
]/[
w
] buttons to
select setting, and then use the Left and
Right [
e
]/[
r
] buttons to set them.
6
When you’ve finished, press the [SETUP]
button.
The setup menu closes.
Speaker Settings
See “Speaker Settings” on page 57.
Speaker Configuration
With these settings, you can specify which speakers are connected and a crossover frequency for each speaker. You
can set the crossover frequencies, distances, and levels of the front Speakers A and front Speakers B independently.
The other speakers (i.e., subwoofer, center, surround, and surround back) use the same crossover frequencies, dis-
tances, and levels for Speakers A and Speakers B. The following crossover frequencies can be specified: “Full Band”,
“40Hz”, “50Hz”, “60Hz”, “70Hz”, “80Hz(THX)”, “90Hz”, “100Hz”, “120Hz”, “150Hz”, or “200Hz”. Specify “Full
Band” for speakers that can output low frequency bass sounds adequately, for example, speakers with a good sized
woofer. For smaller speakers, specify a crossover frequency. Sounds below the crossover frequency will be output by
the subwoofer instead of the speaker. Refer to your speaker’s manuals to determine the optimum crossover frequen-
cies.
If you set up your speakers using Audyssey MultEQ
®
XT Room Correction and Speaker Setup, please make sure
manually that any THX speakers are set to “80Hz(THX)” crossover.
Subwoofer
1ch:
Audio signal is outputted from SW1 jack only.
2ch:
Audio signal is outputted from SW1 and SW2 jacks (default).
No:
Select if no subwoofer is connected.
Front
*1
Full Band, 40Hz, 50Hz, 60Hz, 70Hz, 80Hz(THX) (default), 90Hz, 100Hz, 120Hz,
150Hz, 200Hz
Center
*2
Surround
*2
Front Wide
*2*3*5*7
Front High
*2*3*7*10
Surr Back
*3*4*6
Full Band, 40Hz, 50Hz, 60Hz, 70Hz, 80Hz(THX), 90Hz, 100Hz, 120Hz, 150Hz,
200Hz
None:
Select if no speaker is connected.