Onkyo TX-NR696 Owners Manual - English - Page 119

Crossover

Get Onkyo TX-NR696 PDF manuals and user guides View all Onkyo TX-NR696 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 119 highlights

Contents ≫ Connections ≫ Playback ≫ Setup ≫ Setting Item Zone 2 Lineout Bi-Amp Speaker Impedance Default Value Setting Details Zone 2 Set an output destination of the audio output from ZONE 2 LINE OUT/ZONE B LINE OUT jack. "Zone 2": When connecting a pre-main amplifier in a separate room (ZONE 2) "Zone B": When connecting a pre-main amplifier, transmitter of wireless headphones, etc. to ZONE B "Front": When connecting a power amplifier (European, Australian and Asian models) • This setting is fixed to "Zone 2" when "Zone Speaker" is set to "Zone 2". No Set whether the front speakers are bi-amp connected. "No": When front speakers are not bi-amp connected "Yes": When front speakers are bi-amp connected • This setting is fixed to "No" if "Zone Speaker" is set to "Zone 2". • This setting cannot be selected when surround back speakers or height speakers are installed. 6 ohms or above Set the impedance (Ω) of the connected speakers. "4ohms": When any of the connected speakers have 4 Ω or more to less than 6 Ω impedance "6 ohms or above": When all the connected speakers have an impedance of 6 Ω or more • For impedance, check the indications on the back of the speakers or their instruction manual. „„2. Crossover Change the settings of crossover frequencies. • As for the THX-certified speakers, the following settings are recommended. -- Crossover frequency → "80 Hz(THX)" -- "LPF of LFE" → "80 Hz" -- "Double Bass" → "Off" Setting Item Front Center Height Default Value 80 Hz (THX) 80 Hz (THX) 80 Hz (THX) Setting Details Select the crossover frequency from "40 Hz" to "200 Hz" to start outputting frequencies for each channel. "Full Band": Full band will be output. • If "Configuration" - "Subwoofer" is set to "No", "Front" is fixed to "Full Band", and the low pitched range of the other channels is output from the front speakers. Refer to the instruction manual of your speakers to make the setting. Select the crossover frequency from "40 Hz" to "200 Hz" to start outputting frequencies for each channel. "Full Band": Full band will be output. • "Full Band" can be selected only when "Front" is set to "Full Band". • If the item cannot be selected even though connection is correct, check if the setting in "Configuration" - "Speaker Channels" matches the number of connected channels. Select the crossover frequency from "40 Hz" to "200 Hz" to start outputting frequencies for each channel. "Full Band": Full band will be output. • "Full Band" can be selected only when "Front" is set to "Full Band". • If the item cannot be selected even though connection is correct, check if the setting in "Configuration" - "Speaker Channels" matches the number of connected channels. 119 Front Panel≫ Rear Panel≫ Remote≫

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
119
Front Panel
≫
Rear Panel
≫
Remote
≫
Contents
≫
Connections
≫
Playback
≫
Setup
≫
Setting Item
Default Value
Setting Details
Zone 2 Lineout
Zone 2
Set an output destination of the audio output from
ZONE 2 LINE OUT/ZONE B LINE OUT jack.
"Zone 2": When connecting a pre-main amplifier in
a separate room (ZONE 2)
"Zone B": When connecting a pre-main amplifier,
transmitter of wireless headphones, etc. to ZONE B
"Front": When connecting a power amplifier
(European, Australian and Asian models)
•
This setting is fixed to "Zone 2" when "Zone
Speaker" is set to "Zone 2".
Bi-Amp
No
Set whether the front speakers are bi-amp
connected.
"No": When front speakers are not bi-amp
connected
"Yes": When front speakers are bi-amp connected
•
This setting is fixed to "No" if "Zone Speaker" is
set to "Zone 2".
•
This setting cannot be selected when surround
back speakers or height speakers are installed.
Speaker
Impedance
6 ohms or above
Set the impedance (Ω) of the connected speakers.
"4ohms": When any of the connected speakers
have 4 Ω or more to less than 6 Ω impedance
"6 ohms or above": When all the connected
speakers have an impedance of 6 Ω or more
• For impedance, check the indications on the
back of the speakers or their instruction manual.
±
2. Crossover
Change the settings of crossover frequencies.
•
As for the THX-certified speakers, the following settings are recommended.
–
Crossover frequency → "80 Hz(THX)"
–
"LPF of LFE" → "80 Hz"
–
"Double Bass" → "Off"
Setting Item
Default Value
Setting Details
Front
80 Hz (THX)
Select the crossover frequency from "40 Hz" to
"200 Hz" to start outputting frequencies for each
channel.
"Full Band": Full band will be output.
•
If "Configuration" - "Subwoofer" is set to "No",
"Front" is fixed to "Full Band", and the low
pitched range of the other channels is output
from the front speakers. Refer to the instruction
manual of your speakers to make the setting.
Center
80 Hz (THX)
Select the crossover frequency from "40 Hz" to
"200 Hz" to start outputting frequencies for each
channel.
"Full Band": Full band will be output.
•
"Full Band" can be selected only when "Front" is
set to "Full Band".
•
If the item cannot be selected even though
connection is correct, check if the setting in
"Configuration" - "Speaker Channels" matches
the number of connected channels.
Height
80 Hz (THX)
Select the crossover frequency from "40 Hz" to
"200 Hz" to start outputting frequencies for each
channel.
"Full Band": Full band will be output.
•
"Full Band" can be selected only when "Front" is
set to "Full Band".
•
If the item cannot be selected even though
connection is correct, check if the setting in
"Configuration" - "Speaker Channels" matches
the number of connected channels.