Onkyo TX SR506 Owner Manual - Page 75

Tuner, AnalogMulti, AM Freq on some models, SW In Sens, AudioTVOut, LipSync, xvColor, Control - b complex

Get Onkyo TX SR506 - AV Receiver PDF manuals and user guides
UPC - 751398008054
View all Onkyo TX SR506 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 75 highlights

Advanced Setup-Continued Tuner ■ AM Freq (on some models) See "AM Frequency Step Setup (on some models)" on page 49. AnalogMulti ■ SW In Sens Some DVD players output the LFE channel from their analog subwoofer output at 15 dB higher than normal. With this setting, you can change the AV receiver's subwoofer sensitivity to match your DVD player. Note that this setting only affects signals connected to the AV receiver's MULTI CH SUBWOOFER jack. You can select 0 dB, 5 dB, 10 dB, or 15 dB. If you find that your subwoofer is too loud, try the 10 dB or 15 dB setting. HDMI ■ AudioTVOut This setting determines whether audio received by an HDMI input is output by the HDMI outputs. You may want to change this setting to On if your TV is connected to an HDMI output and you want to listen to audio from an HDMI component through your TV's speakers. Normally, it should be set to Off. Off: HDMI audio is not output (default). On: HDMI audio is output. Notes: • If On is selected and the signal can be output by the TV, the AV receiver will output no sound through its speakers. • When TV Control is enabled, this setting is set to Auto. • With some TVs and input signals, no sound may be output even if On is selected. • When the AudioTVOut setting is set to On, or TV Control is set to Enable and you're listening through your TV's speakers (see page 28), if you turn up the AV receiver's volume control, the sound will be output by the AV receiver's speakers. To stop the AV receiver's speakers producing sound, change the settings, change your TV's settings, or turn down the AV receiver's volume. ■ LipSync The Lip Sync function can automatically synchronize HDMI audio and video that's gotten out of sync due to the complex digital video processing being performed by your HDMI-compatible TV. With HDMI Lip Sync, the audio delay required to synchronize the audio and video is calculated and applied automatically by the AV receiver. Disable: HDMI lip sync disabled. Enable: HDMI lip sync enabled. Notes: • This function works only if your HDMI-compatible TV supports HDMI Lip Sync. • You can check the amount of delay being applied by the HDMI Lip Sync function on the A/V Sync screen (see page 72). ■ xvColor If your HDMI source and HDMI-compatible TV both support the "x.v.Color," you can enable "x.v.Color" on the AV receiver with this setting. Disable: "x.v.Color" disabled. Enable: "x.v.Color" enabled. ■ Control This function allows RIHD-compatible components connected via HDMI to be controlled with the AV receiver. Disable: RIHD disabled. Enable: RIHD enabled. Notes: • RIHD, which stands for Remote Interactive over HDMI, is the name of the system control function found on Onkyo components. The AV receiver can be used with CEC (Consumer Electronics Control), which allows system control over HDMI and is part of the HDMI standard. CEC provides interoperability between various components, however, operation with components other than RIHD-compatible components and recommended components cannot be guaranteed. • Select Disable if a connected component is incompatible or you're not sure about its compatibility. • If operation is unreliable when set to Enable, select Disable instead. 75

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
75
Advanced Setup
—Continued
Tuner
■
AM Freq (on some models)
See “AM Frequency Step Setup (on some models)” on
page 49.
AnalogMulti
■
SW In Sens
Some DVD players output the LFE channel from their
analog subwoofer output at 15 dB higher than normal.
With this setting, you can change the AV receiver’s sub-
woofer sensitivity to match your DVD player. Note that
this setting only affects signals connected to the AV
receiver’s MULTI CH SUBWOOFER jack.
You can select 0 dB, 5 dB, 10 dB, or 15 dB.
If you find that your subwoofer is too loud, try the 10 dB
or 15 dB setting.
HDMI
■
AudioTVOut
This setting determines whether audio received by an
HDMI input is output by the HDMI outputs. You may
want to change this setting to On if your TV is connected
to an HDMI output and you want to listen to audio from
an HDMI component through your TV’s speakers. Nor-
mally, it should be set to Off.
Off:
HDMI audio is not output (default).
On:
HDMI audio is output.
Notes:
•
If On is selected and the signal can be output by the
TV, the AV receiver will output no sound through its
speakers.
•
When TV Control is enabled, this setting is set to
Auto.
•
With some TVs and input signals, no sound may be
output even if On is selected.
•
When the AudioTVOut setting is set to On, or TV
Control is set to Enable and you’re listening through
your TV’s speakers (see page 28), if you turn up the
AV receiver’s volume control, the sound will be output
by the AV receiver’s speakers. To stop the AV
receiver’s speakers producing sound, change the set-
tings, change your TV’s settings, or turn down the AV
receiver’s volume.
■
LipSync
The Lip Sync function can automatically synchronize
HDMI audio and video that’s gotten out of sync due to
the complex digital video processing being performed by
your HDMI-compatible TV. With HDMI Lip Sync, the
audio delay required to synchronize the audio and video
is calculated and applied automatically by the AV
receiver.
Disable:
HDMI lip sync disabled.
Enable:
HDMI lip sync enabled.
Notes:
•
This function works only if your HDMI-compatible
TV supports HDMI Lip Sync.
•
You can check the amount of delay being applied by
the HDMI Lip Sync function on the A/V Sync screen
(see page 72).
■
xvColor
If your HDMI source and HDMI-compatible TV both
support the “x.v.Color,” you can enable “x.v.Color” on
the AV receiver with this setting.
Disable:
“x.v.Color” disabled.
Enable:
“x.v.Color” enabled.
■
Control
This function allows RIHD-compatible components
connected via HDMI to be controlled with the AV
receiver.
Disable:
RIHD disabled.
Enable:
RIHD enabled.
Notes:
•
RIHD, which stands for Remote Interactive over
HDMI, is the name of the system control function
found on Onkyo components. The AV receiver can be
used with CEC (Consumer Electronics Control),
which allows system control over HDMI and is part of
the HDMI standard. CEC provides interoperability
between various components, however, operation with
components other than RIHD-compatible components
and recommended components cannot be guaranteed.
•
Select Disable if a connected component is incompat-
ible or you’re not sure about its compatibility.
•
If operation is unreliable when set to Enable, select
Disable instead.