Onkyo TX-SV313 Owner Manual - Page 7
TX-SV313PRO
View all Onkyo TX-SV313 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 7 highlights
AM Antenna Connections An AM loop antenna is included in the installation instructions bag. Take out the connection line and connect it to the AM antenna terminals. This loop antenna can be placed on top of any stable surface or attached to a wall. Try several positions to determine which gives the best reception. Be sure the antenna is not near a speaker, power cord, television set, VCR. or motorized appliances. When using an external AM antenna, do not remove the loop antenna; connect both antennas to the AM antenna terminals. AM loop antenna assembly Connect to the AM antenna terminals. Remove the vinyl tie and take out the connection line. Bend in the reverse direction. a With the antenna on to of arty stable surface Mount b. With the antenna attache° to a wall installation hole Mount on a wall. etc. Turntable Connections (PHONO) Connect the output of the turntable to the PHONO jacks. Be sure to connect the ground (earth) lead wire from the turntable to the ground terminal (GND). Lack of proper ground connection will cause hum Turntables not provided with GND wires do not need to be connected. 1. Place the turntable on a firm shelf or deck tree from vibrations (especially those generated by the speaker system). If the turntable is permitted to pick up such unwanted vibrations, not only with the performance of the unit drop, but distortion in the bass frequencies and howling in the speakers may also occur. 2. Check the turntable instruction manual for any other precautions. 3. The loud noises that occur when connecting and disconnecting. replacing the cartridge or lowering the tonearm could damage the speakers. Always turn the power switch off before making connections. Tape Deck and Graphic Equalizer Connections (TAPE-1, TAPE-2) 1. This unit has facilities for two tape decks. If you are using only one tape deck, connect it to the TAPE-1 jacks. If you have two tape decks, connect one to the TAPE-1 jacks and the other to the TAPE-2 jacks. 2. Connect the output of the tape decks to the TAPE-1 and TAPE-2 "PLAY" jacks. Connect the input of the tape decks to the TAPE-1 and TAPE-2 "REC" jacks of the unit. For more details, refer to your tape deck instruction manual. 3. To connect a graphic equalizer, too, use the TAPE-2 jacks and connect the second tape deck to the tape jacks of the equalizer. (See the figure) To connect a graphic equalizer and second tape deck to the TAPE-2 jacks. To TAPE-2 "REC" Jacks of TX-SV313PRO To TAPE-2 'PLAY- jacks of TX-81:313PR° Er UAL IN PUT OUT PUT R C P r Graphic equalizer NOTE: 41)Vi reception is easily affected by television sets and VCRs. . therefore, AM reception may be poor if this unit is placed too I close to a TV or a VCR. I Speaker Connections (SPEAKERS) 1. Connect the speakers to "FRONT' and/or "REAR" terminals. The center speaker should be connected to CENTER terminals. 2. When connecting speakers, proper polarity is important. Always connect the (+) terminal (red) on this equipment to the (+) terminal on the speaker and the (-) terminal (black) on this equipment to the (-) terminal on the speaker. 3. Do not connect a single speaker in parallel to the right and left channel outputs. 4. Use speaker cables that have a low impedance and that are as short as possible. • Attach speaker cables to the rear panel speaker terminals with care, being sure that connections are made firmly and that there is no possibility of a short circuit occurring. Compact Disc Player or Other Component C.....-tions (CD) Connect the output of the CD player or an additional audio component to the CD jacks. An ONKYO CD player with remote control that has the R I mark can be operated by the TX-SV313PRO. (Please refer to "Connections for Remote Control".) For more details, refer to your CD player instruction manual. L ( )-LJ L R REC PLAY Second tape deck J 4. If you have an ONKYO tape deck with the RI remote control jack. connect it to the TAPE-1 jacks. Please refer to the section "Connections for Remote Control" regarding connection of the remote control cable. Video Disc Player (or Video Cassette Player) Connections (VIDEO-1) Connect the VIDEO output of the video disc player to the TXSV313PRO (VIDEO) VIDEO-1 "IN" jack and the AUDIO output to the (AUDIO) VIDEO-1 "IN" jack. The VIDEO-1 jack is only for playback there is no OUT jack. For more details, refer to the video disc player instruction manual. Video Cassette Recorder Connections (VIDEO-2) 1. Connect the VIDEO output of the VCR to the rear panel (VIDEO) VIDEO-2 "IN" jack and the VIDEO input of the VCR to the rear panel (VIDEO) VIDEO-2 "OUT" jack. Then connect the AUDIO output of the VCR to the (AUDIO) VIDEO-2 L and R "IN" jacks. Finally, connect the AUDIO input of the VCR to the (AUDIO) VIDEO-2 L and R "OUT' jacks. 2. When using a playback-only VCR, only the output connections need to be performed. 3. For more details, refer to the VCR instruction manual. -6-