Optoma GT1080DARBEE GT1080Darbee User Manual - Page 40

Replacing the lamp continued, Lamp Reset: i Press Menu

Get Optoma GT1080DARBEE PDF manuals and user guides View all Optoma GT1080DARBEE manuals
Add to My Manuals
Save this manual to your list of manuals

Page 40 highlights

MAINTENANCE Replacing the lamp (continued) 2 5 4 3 6 1 Procedure: 1. Switch off the power to the projector by pressing the " " button on the remote control or the projector keypad. 2. Allow the projector to cool down for at least 30 minutes. 3. Disconnect the power cord. 4. Unscrew the screw on the cover. 1 5. Remove the cover. 2 6. Remove the lamp cord.3 7. Unscrew the screw on the lamp module.4 8. Lift up the lamp handle. 5 9. Remove the lamp module carefully. 6 10. To replace the lamp module, reverse the previous steps. 11. Turn on the projector and reset the lamp timer. 12. Lamp Reset: (i) Press "Menu"  (ii) Select "Setup"  (iii) Select "Lamp Settings"  (iv) Select "Lamp Reset"  (v) Select "Yes". Note: ‡‡ The screw on the lamp cover and the lamp cannot be removed. ‡‡ The projector cannot be turned on if the lamp cover has not been placed back on the projector. ‡‡ Do not touch the glass area of the lamp. Hand oil can cause the lamp shatter. Use a dry cloth to clean the lamp module if it was accidentally touched. 40 English

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
English
40
MAINTENANCE
Replacing the lamp (continued)
4
1
6
2
3
5
Procedure:
1.
Switch off the power to the projector by pressing the "
" button on the remote control or the projector
keypad.
2.
Allow the projector to cool down for at least 30 minutes.
3.
Disconnect the power cord.
4.
Unscrew the screw on the cover.
1
5.
Remove the cover.
2
6.
Remove the lamp cord.
3
7.
Unscrew the screw on the lamp module.
4
8.
Lift up the lamp handle.
5
9.
Remove the lamp module carefully.
6
10.
To replace the lamp module, reverse the previous steps.
11.
Turn on the projector and reset the lamp timer.
12.
Lamp Reset: (i) Press "Menu"
(ii) Select "Setup"
(iii) Select "Lamp Settings"
(iv) Select "Lamp
Reset"
(v) Select "Yes".
Note°
±
The screw on the lamp cover and the lamp cannot be removed.
±
The projector cannot be turned on if the lamp cover has not been placed back on the projector.
±
Do not touch the glass area of the lamp. Hand oil can cause the lamp shatter. Use a dry cloth to clean
the lamp module if it was accidentally touched.