Optoma GT1080HDR EH412ST User Manual - Page 53

Other problems, Remote control problems, Lamp burns out or makes a popping sound

Get Optoma GT1080HDR PDF manuals and user guides View all Optoma GT1080HDR manuals
Add to My Manuals
Save this manual to your list of manuals

Page 53 highlights

ADDITIONAL INFORMATION B lurry double image ‡‡ Press "3D" button and switch to "Auto" to avoid normal 2D image is blurry double image. T wo images, side-by-side format ‡‡ Press "3D" button and switch to "Side by Side" for input signal is HDMI 1.3 2D 1080i side-by-side. I mage does not display in 3D ‡‡ Check if the battery of 3D glasses is drained. ‡‡ Check if the 3D glasses is turned on. ‡‡ When the input signal is HDMI 1.3 2D (1080i side-by-side half), press "3D" button and switch to "Side by Side". Other problems T he projector stops responding to all controls ‡‡ If possible, turn off the projector, then unplug the power cord and wait at least 20 seconds before reconnecting power. L amp burns out or makes a popping sound ‡‡ When the lamp reaches its end of life, it will burn out and may make a loud popping sound. If this happens, the projector will not turn on until the lamp module has been replaced. To replace the lamp, follow the procedures in the "Replacing the Lamp" section on pages 41-42. Remote control problems If the remote control does not work ‡‡ Check the operating angle of the remote control is pointed within ±15° to the IR receiver on the projector. ‡‡ Make sure there are not any obstructions between the remote control and the projector. Move to within 6 m (20 ft) of the projector. ‡‡ Make sure batteries are inserted correctly. ‡‡ Replace batteries if they are exhausted. English 53

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
English
53
ADDITIONAL INFORMATION
Blurry double image
±
Press "3D" button and switch to "Auto" to avoid normal 2D image is blurry double image.
Two images, side-by-side format
±
Press "3D" button and switch to "Side by Side" for input signal is HDMI 1.3 2D 1080i side-by-side.
Image does not display in 3D
±
Check if the battery of 3D glasses is drained.
±
Check if the 3D glasses is turned on.
±
When the input signal is HDMI 1.3 2D (1080i side-by-side half), press "3D" button and switch to "Side
by Side".
Other problems
The projector stops responding to all controls
±
If possible, turn off the projector, then unplug the power cord and wait at least 20 seconds before
reconnecting power.
Lamp burns out or makes a popping sound
±
When the lamp reaches its end of life, it will burn out and may make a loud popping sound. If this
happens, the projector will not turn on until the lamp module has been replaced. To replace the lamp,
follow the procedures in the "Replacing the Lamp" section on pages
41-42
.
Remote control problems
If the remote control does not work
±
Check the operating angle of the remote control is pointed within ²15° to the IR receiver on the
projector.
±
Make sure there are not any obstructions between the remote control and the projector. Move to within
6 m (20 ft) of the projector.
±
Make sure batteries are inserted correctly.
±
Replace batteries if they are exhausted.