Panasonic CQVD7700U CQVD7500U User Guide - Page 30
Small, Large, Surround
View all Panasonic CQVD7700U manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 30 highlights
E N MENU: Audio Settings (for VD7700U) (continued) G L I S : Previous menu H : Exit 48 Menu Setting Value Operations SP SETUP (continued) SURROUND (Surround speaker setting) LARGE : for large speakers, when bass playback is possible (at least 100 Hz or lower) SMALL : for small speakers, or when bass playback is not possible Panel SURROUND a NONE or SMALL or LARGE Remote NONE : when not using surround speakers default: LARGE [}] or [{] a []] or [[] a [ENTER] SUB • W (Subwoofer speaker setting) A subwoofer (option, CJ-SW38 recommended) is required. A power amplifier (option) is also required for connecting a subwoofer. YES : when using a subwoofer NO : when not using a subwoofer default: NO Panel SUB • W a NO or YES Remote [}] or [{] a []] or [[] a [ENTER] SP LEVEL (Speaker Level) (Adjusting the output balance of each speaker) FRONT L (Left front speaker output balance) CENTER (Center speaker output balance) FRONT R (Right front speaker output balance) R¡SURROUND (Right surround speaker output balance) L¡SURROUND (Left surround speaker output balance) SUB¡W (Subwoofer speaker output balance) Setting range: -12 dB to +12 dB (1 dB steps) Default: ± 0 dB for all speakers A test signal (a continuous tone) is output from each speaker for approximately two seconds. Adjust the output balance so that the tone appears to have the same volume from each speaker. Adjusting the output balance: Adjust the volume of all of the other speakers to the volume level of the speaker from which the test signal appears to be the quietest. ¡If the speaker setting is "NONE" or "NO" for a speaker, the test signal is not output and that speaker cannot be selected. (a page 63) ¡Turn [VOLUME] or press [}] or [{] (VOLUME) to adjust the volume of the test signal. Panel q Touch the image of the speaker you want to set. w [ : UP ] : Down Touch to select Remote q [}] or [{] w [[] : UP []] : Down 64 CQ-VD7700U/VD7500U E N G L I : Previous menu S : Exit H Menu Setting Value Operations 49 SP DELAY (Speaker Delay) (Adjusting the timing with which the audio from each speaker reaches the listener's position) CENTER Setting range: Center speaker... 0 ms to 5 ms (1 ms steps) Surround speakers... 0 ms to 15 ms (1 ms steps) 1 ms = 0.001 seconds Panel q Touch a speaker image. (Center or Surround) w [ : Long ] : Short (Center speaker delay time setting) Default: 0 ms for all speakers Remote SURROUND q [}] or [{] (Surround speaker delay time setting) ¡Make this adjustment while listening to sound. ¡If the speaker setting is "NONE" for a speaker, that speaker cannot be selected. (a page 63) w [[] : Long []] : Short VTR LEVEL (Setting the VTR (VTR1/VTR2) input Level) Make this setting if it is not possible to adjust the volume through the connected device (on the output side). Note: This setting is adjustable for an external device that is connected to VTR1 or VTR2. (e.g. VCR) Lower Higher -6 dB -4 dB -2 dB ±0 dB +2 dB +4 dB +6 dB : Input level default: ±0 dB Notes: ¡If the input level from VTR1/VTR2 is too high, the audio will not be output normally. Adjust the input level so that "OVER" does not appear. ¡After setting the input level The volume can be adjusted by turning the volume knob or pressing [}] or [{] (VOLUME) on the remote control. Panel ] : Lower [ : Higher Remote []] : Lower [[] : Higher 65 CQ-VD7700U/VD7500U