Panasonic EY6803 EY6803 User Guide - Page 6

Operation

Get Panasonic EY6803 - HAMMER DRILL DRIVER 12V PDF manuals and user guides View all Panasonic EY6803 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 6 highlights

14)Do not attempt to disassemble the battery pack housing. 15)Do not store the tool and battery pack in locations where the temperature may reach or exceed 50°C (122°F) (such as a metal tool shed, or a car in the summer), which can lead to deterioration of the storage battery. 16)Do not charge battery pack when the temperature is BELOW 0°C (32°F) or ABOVE 40°C (104°F). This is very important in order to maintain optimal condition of the battery pack. 17)Do not incinerate the battery pack. It can explode in a fire. 18)Avoid dangerous environment. Do not use charger in damp or wet locations. 19)The charger is designed to operate on standard household electrical power only. Do not attempt to use it on any other voltage! 20)Do not abuse cord. Never carry charger by cord or yank it to disconnect from outlet. Keep cord away from heat, oil and sharp edges. 21)Charge the battery pack in a well ventilated place, do not cover the charger and battery pack with a cloth, etc., while charging. 22)Use of an attachment not recommended may result in a risk of fire, electric shock, or personal injury. 23)Do not short the battery pack. A battery short can cause a large current flow, over heating and create the risk of fire or personal injury. 24)NOTE: If the supply cord of this appliance is damaged, it must only be replaced by a repair shop authorized by the manufacturer, because special purpose tools are required. 25)TO REDUCE THE RISK OF ELECTRIC SHOCK, THIS APPLIANCE HAS A POLARIZED PLUG (ONE BLADE IS WIDER THAN THE OTHER). This plug will fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician to install the proper outlet. Do not change the plug in any way. IV. OPERATION CAUTION: Use of a concrete drill bit larger than the recommended size may cause damage to the driver. Chuck NOTE: Grease for bit Grease the oval indentation on the bit with the supplied grease at least once a month. 1. To insert the bit 1-1. Insert a bit into the mounting hole, and turn it slightly to locate an engaged position. 1-2. At the engaged position, push the bit as far as it goes. Make sure that the bit is fixed by pulling it. SDS PLUS type shank 2. To remove the bit 2-1. Depress the chuck cover and pull the bit. Bit adapter Use a bit adapter (standard) and bit. 1. Remove the bit adapter from the bit adapter holder on the main unit. 2. Pull the bit holder. ( ) 3. Insert the bit. ( ) 4. Make sure the bit is inserted firmly by pulling it lightly. 5. Insert the bit adapter into the mounting hole and turn to Bit holder locate an engaged position. -  -

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
-
6
-
14)Do not attempt to disassemble the
battery pack housing.
15)Do not store the tool and battery pack
in locations where the temperature
may reach or exceed 50°C (1±±°F)
(such as a metal tool shed, or a car
in the summer), which can lead to
deterioration of the storage battery.
16)Do not charge battery pack when the
temperature is BELOW 0°C (3±°F)
or ABOVE 40°C (104°F). This is very
important in order to maintain optimal
condition of the battery pack.
17)Do not incinerate the battery pack. It
can explode in a fire.
18)Avoid dangerous environment. Do not
use charger in damp or wet locations.
19)The charger is designed to operate on
standard household electrical power
only. Do not attempt to use it on any
other voltage!
±0)Do not abuse cord. Never carry charger
by cord or yank it to disconnect from
outlet. Keep cord away from heat, oil
and sharp edges.
±1)Charge the battery pack in a well
ventilated place, do not cover the
charger and battery pack with a cloth,
etc., while charging.
±±)Use of an attachment not recommended
may result in a risk of fire, electric
shock, or personal injury.
±3)Do not short the battery pack. A battery
short can cause a large current flow,
over heating and create the risk of fire
or personal injury.
±4)NOTE: If the supply cord of this
appliance is damaged, it must only be
replaced by a repair shop authorized
by the manufacturer, because special
purpose tools are required.
±5)TO REDUCE THE RISK OF ELECTRIC
SHOCK, THIS APPLIANCE HAS A
POLARIZED PLUG (ONE BLADE IS
WIDER THAN THE OTHER).
This plug will fit in a polarized outlet
only one way. If the plug does not fit
fully in the outlet, reverse the plug. If
it still does not fit, contact a qualified
electrician to install the proper outlet.
Do not change the plug in any way.
I
V
.
OPERATION
CAUTION:
Use of a concrete drill bit larger than
the recommended size may cause
damage to the driver.
Chuck
NOTE:
Grease for bit
Grease the oval indentation on
the bit with the supplied grease
at least once a month.
1. To insert the bit
1-1. Insert a bit into the mounting hole, and
turn it slightly to locate an engaged
position.
1-±. At the engaged position, push the bit
as far as it goes. Make sure that the
bit is fixed by pulling it.
SDS PLUS type
shank
2. To remove the bit
±-1.
Depress the chuck cover and pull the bit.
Bit adapter
Use a bit adapter (standard) and bit.
1. Remove the bit adapter from
the bit adapter holder on the
main unit.
±. Pull the bit holder. (
)
3. Insert the bit. (
)
Bit
holder
4. Make sure the bit is inserted
firmly by pulling it lightly.
5. Insert the bit adapter into the
mounting hole and turn to
locate an engaged position.