Panasonic EY7411 EY7411 User Guide - Page 9

Convenient function settings buzzer, sound setting/double tightening, counting prevention time

Get Panasonic EY7411 - CORDLESS DRILL & DRIVER PDF manuals and user guides View all Panasonic EY7411 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 9 highlights

Count system setting Press . "UP" or "DOWN" will begin to flash. Next select ("UP") or ("DOWN"). ● Press and hold the ( ) or ( ) buttons to vary the value continuously. < Count System "UP" > ● Displays the count for the number of screws driven. ( Set number ) The settings are activated by pushing . ● When the set number of screws is reached, the buzzer sounds and the count value resets to zero. < Count System "DOWN" > ● Displays the count for the remain- ing number of screws to be driven. ( Set number ) ● When the set number of screws to be driven is reached, the buzzer sounds and the count value resets to original set number. 3. The settings are activated by pushing . ● The previous setting will be cancelled and replaced with the new setting. 4. To prevent changes in the set values due to operational errors. ● Turn the HOLD switch to ON. ON Convenient function settings (buzzer sound setting/double tightening count­ing prevention time setting) Buzzer sound setting 1. Press for 2 or more seconds while the control panel is illuminat­ed. ● Count display lamp "F1" is illumi- nated. 2. The buzzer sound can be selected with when "F1" is illuminated. Operation Display b3 b2 b1 b0 Sound Frequency High pitched sound (Approx. 4 kHz) Medium pitched sound (Approx. 3 kHz) Low pitched sound (Approx. 2 kHz) No sound (OFF) ● If is pressed while in the buzzer mode, the buzzer sound saved from the previous setting is displayed. 3. The settings are activated by pushing . 4. To prevent changes in the set values due to operational errors. ● Turn the HOLD switch to ON. ON Double tightening counting prevention time setting 1. Press for 2 or more seconds while the control panel is illuminat­ed. ● Count display lamp "F1" is illuminated. 2. Press again to illuminate "F2" and select the time with . Operation Display No. of seconds 30 3 seconds 1 0.1 second 0 OFF Following the screw count, screw driving within the set number of seconds is not counted. ● If is pressed while in the time mode, the time sett­ing saved from the previous setting is displayed. 3. The settings are activated by pressing . 4. To prevent changes in the set values due to operational errors. ● Turn the HOLD switch to ON. ON To change the screw count while in use 1. Release the hold switch. 2. Adjust the count value with . ● The displayed number of screws -  -

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
-
9
-
Count system setting
Press
. “UP” or “DOWN” will begin
to flash. Next select
(“UP”) or
(“DOWN”).
●
Press and hold the (
) or (
) but-
tons to vary the value continuously.
< Count System “UP” >
● Displays the count for the number
of screws driven.
(
Set number
)
The settings are activated by pushing
.
● When the set number of screws is
reached, the buzzer sounds and
the count value resets to zero.
< Count System “DOWN” >
● Displays the count for the remain
-
ing number of screws to be driven.
( Set number
)
● When the set number of screws to
be driven is reached, the buzzer
sounds and the count value resets
to original set number.
3. The settings are activated by pushing
.
● The previous setting will be can
-
celled and replaced with the new
setting.
4. To prevent changes in the set values
due to operational errors.
ON
● Turn the HOLD switch
to ON.
Convenient function settings (buzzer
sound setting/double tightening
counting prevention time setting)
Buzzer sound setting
1. Press
for ± or more seconds while
the control panel is illuminated.
● Count display lamp “F1” is illumi
-
nated.
±. The buzzer sound can be selected
with
when “F1” is illuminated.
Operation
Display
Sound Frequency
b3
High pitched sound
(Approx. 4 kHz)
b±
Medium pitched
sound (Approx. 3
kHz)
b1
Low pitched sound
(Approx. ± kHz)
b0
No sound (OFF)
● If
is pressed while in the buzzer
mode, the buzzer sound saved
from the previous setting is dis-
played.
3. The settings are activated by pushing
.
4. To prevent changes in the set values
due to operational errors.
ON
● Turn the HOLD switch
to ON.
Double tightening counting preven-
tion time setting
1. Press
for ± or more seconds while
the control panel is illuminated.
● Count display lamp “F1” is illumi
-
nated.
±. Press
again to illuminate “F±” and
select the time with
.
Operation Display
No. of
seconds
Following the
screw count,
screw driving
within the set
number of
seconds is
not counted.
30
3
seconds
1
0.1
second
0
OFF
● If
is pressed while in the time
mode, the time setting saved from
the previous setting is displayed.
3. The settings are activated by pressing
.
4. To prevent changes in the set values
due to operational errors.
ON
● Turn the HOLD switch
to ON.
To change the screw count while in
use
1. Release the hold switch.
±. Adjust the count value with
.
● The displayed number of screws