Panasonic FV-05-11VK1 Installation Instructions - Page 6

FEATURE CONTINUED Optimum Ventilation Performance: Duct length, elbows and other factors increase static pressure which can hinder the performance of most ventilation fans. This fan utilizes SmartFlow microchip technology that monitors the static pressure in the system and speeds up or slows down the rpm of the fan depending upon the amount of resistance within the ducts. This feature allows the fan to perform as rated and avoid potential installation issues. Outstanding Energy Savings: The WhisperGreen Select Line of fans are built using DC motor technology. The DC motor is 30% - 70% more energy efficient than the minimum ENERGY STAR requirements. Pick-A-Flow Feature All the WhisperGreen Select base models of fans come with Pick-A-Flow speed options. The Pick-A-Flow switch on the face of all WhisperGreen Select fans allows the option to choose 50 - 80 - 110 CFM for the FV-05-11VK1, FV-05-11VKS1 or 110 - 130 - 150 CFM for the FV-11-15VK1. These fans can run continuously or intermittently, depending upon the needs of the owner. AIR VOLUME (CFM) 05-11 50 80 110 MODEL 11-15 MODEL110130150 Pick-A-Flow switch AIR VOLUME (CFM) 05-11 50 80 110 MODEL 11-15 MODEL110130150 Air volume type (CFM) Factory setting FV-05-11VKS1 50 80 110 FV-05-11VK1 80 CFM FV-11-15VK1 110 130 150 130 CFM INDICATION (PLUG 'N PLAY FUNCTION DEVICES) PLUG 'N PLAY Modular Component Accessories Sold Separately, Not Included With Base Model Fan Note that there is ONLY ONE Plug 'N Play slot to insert the Multi-Speed module within the base model fan. There are TWO interchangeable Plug 'N Play slots to insert the Condensation Sensor module, Motion Sensor module or Nite-GloTM LED Night Light module within the base model fan. 6 AIR VOLUME (CFM) 05-11 50 80 110 MODEL 11-15 MODEL110130150 FV-VS15VK1 Multi-Speed module allows the fan to run continuously at lower speeds to maintain ventilation standards to meet Indoor Air Quality and then boost up to high speed to meet intermittent needs for 'Spot' or 'Point Source' exhaust needs. The FV-VS15VK1 Modular Component will operate for both the FV-05-11VK1 and the FV-11-15VK1 matching the appropriate Multi-Speed setting shown below. The FV-05-11VKS1 comes with the FV-VS15VK1 Multi-Speed module. It is not necessary to purchase this component. Note the options on the face of the FV-VS15VK1 Multi-Speed module to choose appropriate levels of airflow (CFM) and time delay before returning back to low speed (TIME). Choosing the Pick-A-Flow setting automatically adjusts the Multi-Speed setting accordingly. As an example,if the Pick-A-Flow Multi-speed setting is 80 CFM, the Multi-Speed settings adjust automatically to be 0, 30, 40, 50, 60 or 70CFM at the lower speeds. The fan will 'boost' to the 80 CFM speed as the high speed setting. Selecting a particular TIME option will cause the fan to run for the selected amount of time before returning to the lower speed setting chosen on the CFM dial. Pick-A-Flow (CFM) Multi-Speed Air volume (CFM) FV-05-11VKS1, 50 0 30 40 40 40 40 40 40 40 FV-05-11VK1 80 0 30 40 50 60 70 70 70 70 (plug-in FV-VS15VK1) 110 0 30 40 50 60 70 80 90 100 110 0 50 60 70 80 90 100 100 100 FV-11-15VK1 130 0 50 60 70 80 90 100 110 110 (plug-in FV-VS15VK1) 150 0 50 60 70 80 90 100 110 120 Delay Time (min) 45 Factory setting: 20 minutes. Delay Time position "0" : Manual wall switch control is 0 minute; without manual wall switch control is 0.5 minute. FV-CSVK1 Condensation Sensor module turns the base fan on or boosts to higher speed when humidity is detected when used in combination with the FV-VS15VK1. The Condensation Sensor works based on calculations from the Psychrometric Chart, or combination of Relative Humidity (RH) and Temperature. This allows the fan to anticipate the formation of condensation and automatically turn on when needed to expel humid air. The Condensation Sensor is pre-set to run for 20 minutes; it will then check the RH and Temperature to detect if the fan needs to run for another 20 minutes cycle.