Panasonic Handheld P2 HD Camcorder with AVC-ULTRA Recording Operating Instruct - Page 103

Chapter 4 Shooting - Setting the time data Verification information on the right-hand six digits Fixed values Sequence No. 24P: 0-4 Other than above: F-fixed Media management information ɾ U
pdated frame flags and valid frame flags ɾ REC mark
Camera image mode Example)ɾ60iɿ600 ɾ60Pɿ608 ɾ30Pɿ308 ɾ24Pɿ248 ɾ24PNɿ24C ɾ50iɿ502 ɾ50Pɿ50A ɾ25Pɿ25A (During shooting)

ɾ
ˎˎ Pɿˎˎ 9 (VFR 30PN or over 60P)
ɾ
ˎˎ Pɿˎˎ 1 (VFR over 60P)
ɾ
ˎˎ Pɿˎˎ D (VFR24PN during shooting)
ɾ
ˎˎ Pɿˎˎ B (VFR25PN or over 50P)
Setting the time code 1 Set the mode for time code in the main menu → [RECORDING SETUP] → [DF MODE]/[TCG]. ff[TC MODE] (When 59.94 Hz) Sets [DF] (Drop frame mode)/[NDF] (non-drop frame mode). In 24PN, the camera always operates in [NDF]. ff[TCG] Sets [FREE RUN] (free run)/[REC RUN] (recording run). 2 Set to [TC PRESET] in the main menu → [RECORDING SETUP]. 3 Set the time code using the control stick. ffScreen display - When pushed down to the right, the digit that has been to set (flashing) moves to the right. - When pushed down to the left, the digit that has been to set (flashing) moves to the left. - When pushed down toward the top, the value of the digit that has been to set (flashing) is raised by one. - When pushed down toward the bottom, the value of the digit that has been to set (flashing) is lowered by one. 4 Press the control stick, enter the values of the time code, and exit the time code settings screen. 5 Use the button to display [TC] and confirm that the set value is displayed. Settable time code range For 59.94 Hz (except for 24PN) 24PN For 50 Hz 00:00:00:00 to 23:59:59:29 00:00:00:00 to 23:59:59:23 00:00:00:00 to 23:59:59:24 @@NOTE tt When using with 24P, the time code setting is adjusted in 5-frame units. When 24PN, adjusted in multiples of 4, and when 720/30PN and 720/25PN, adjusted to even numbers. Also, the time code cannot be set during recording. tt If you exit the time code setting screen without pressing the control stick, the set values are disabled. tt When the button is pressed while in the time code setting screen, the value is reset to 0. Time code function during battery replacement Even during battery replacement, the backup mechanism functions, allowing the time code generator to continue operating. When each item of the system mode has been changed, the time code of free run may shift. Turn on the power again, check the time code, and reset it, if necessary. @@NOTE tt When the power switch has been switched to → → , the backup accuracy of the time code in the free run mode is approximately ±2 frames. Time codes in variable frame rate ffIn 24PN, recording is 24 frames, output is 30 frames, which matches 2:3 pull-down images. ffThe advance rate of the recording and output time code matches real time only when the image frame rate is 24P. When 60P, recording advance rate is 60/24 times. In this case, the camera switches to [REC RUN] fixed operation and the time code value that is output when recording starts matches the recording time code. - 103 -