Panasonic KX-TG2248S 2.4 Ghz Digital Cdl - Page 51

Troubleshooting

Get Panasonic KX-TG2248S - 2.4 GHz Digital Cordless Phone Answering System PDF manuals and user guides
UPC - 037988473687
View all Panasonic KX-TG2248S manuals
Add to My Manuals
Save this manual to your list of manuals

Page 51 highlights

Troubleshooting Cordless Telephone Problem "No link to base. Place on cradle and try again." is displayed and an alarm tone sounds. Static, sound cuts in/out, fades. Interference from other electrical units. The handset does not ring. The handset display is blank. You cannot program function items. While programming or searching, the unit starts to ring and stops the program/ search. You cannot make a call with the handset. You cannot redial. The unit does not display the caller's name and/or phone number. Cause & Remedy • You are too far from the base unit. Walk closer and try again. • Place the handset on the base unit and try again. • Plug in the AC adaptor. • Raise the base unit antenna. • Move the handset and the base unit away from other electrical appliances (p. 3). • Walk closer to the base unit. • Raise the base unit antenna. • Select a clearer channel (p. 23, 36). • The ringer volume is set to OFF. Set to HIGH, MEDIUM or LOW (p. 17). • Charge the battery fully (p. 8). • Programming is not possible while the unit is being used. • Do not pause for over 60 seconds while programming. • Walk closer to the base unit. • A call is coming in. To answer the call, press [ ] or [ ]. Start again from the beginning after hanging up. • Your handset is in remote operation mode (p. 41). Exit by pressing [OFF]. • If the last number dialed was more than 32 digits long, the number will not be redialed correctly. • You need to subscribe to a Caller ID service. • Other telephone equipment may be interfering with your phone. Disconnect it and try again. • Other electrical appliances connected to the same outlet may be interfering with Caller ID. • Telephone line noise may be affecting Caller ID. • The caller requested not to send his/her Caller ID information (p. 25). • If a Caller ID box is connected between the unit and the telephone wall jack, disconnect the Caller ID box or plug the unit directly into the wall jack. For assistance, please call: 1-800-211-PANA(7262) 51 Useful Information

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
Useful Information
For assistance, please call: 1-800-211-PANA(7262)
51
Troubleshooting
Cordless Telephone
Problem
Cause & Remedy
“
No link to base.
Place on cradle and
try again.
”
is displayed
and an alarm tone sounds.
•
You are too far from the base unit. Walk closer
and try again.
•
Place the handset on the base unit and try
again.
•
Plug in the AC adaptor.
•
Raise the base unit antenna.
Static, sound cuts in/out,
fades. Interference from other
electrical units.
•
Move the handset and the base unit away
from other electrical appliances (p. 3).
•
Walk closer to the base unit.
•
Raise the base unit antenna.
•
Select a clearer channel (p. 23, 36).
The handset does not ring.
•
The ringer volume is set to OFF. Set to HIGH,
MEDIUM or LOW (p. 17).
The handset display is blank.
•
Charge the battery fully (p. 8).
You cannot program function
items.
•
Programming is not possible while the unit is
being used.
•
Do not pause for over 60 seconds while
programming.
•
Walk closer to the base unit.
While programming or
searching, the unit starts to
ring and stops the program/
search.
•
A call is coming in. To answer the call, press
[
]
or
[
. Start again from the beginning
after hanging up.
You cannot make a call with
the handset.
•
Your handset is in remote operation mode
(p. 41). Exit by pressing
[OFF]
.
You cannot redial.
•
If the last number dialed was more than
32 digits long, the number will not be redialed
correctly.
The unit does not display the
caller
’
s name and/or phone
number.
•
You need to subscribe to a Caller ID service.
•
Other telephone equipment may be interfering
with your phone. Disconnect it and try again.
•
Other electrical appliances connected to the
same outlet may be interfering with Caller ID.
•
Telephone line noise may be affecting Caller
ID.
•
The caller requested not to send his/her
Caller ID information (p. 25).
•
If a Caller ID box is connected between the
unit and the telephone wall jack, disconnect
the Caller ID box or plug the unit directly into
the wall jack.