Panasonic PT-MZ670 Series Operating Instructions - Page 141
[digital Link Menu], [wired Lan], English - 141
View all Panasonic PT-MZ670 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 141 highlights
Chapter 4 Settings - [NETWORK/USB] menu [SIGNAL QUALITY] [SIGNAL QUALITY] is a numerical value of the amount of error, and the display color changes to green, yellow, or red depending on that value. Check the signal quality level while receiving a signal from the twisted-pair-cable transmitter. ff [MAX]/[MIN]: Maximum/minimum value of the amount of error ff Green (-12 dB or lower) → normal signal quality level. ff Yellow (-11 to -8 dB) → caution level that noise may appear on the screen. ff Red (-7 dB or more) → abnormal level that synchronization is disrupted or not possible to receive. [DIGITAL LINK MENU] When the optional DIGITAL LINK output supported device (Model No.: ET‑YFB100G, ET‑YFB200G) is connected to the terminal, the main menu of the connected DIGITAL LINK output supported device is displayed. Refer to the Operating Instructions of the DIGITAL LINK output supported device for details. Note ff When the [NETWORK/USB] menu → [NETWORK CONTROL] → [EXTRON XTP] is set to [ON], [DIGITAL LINK MENU] cannot be selected. [WIRED LAN] Perform the connection setting to use the wired LAN. 1) Press as to select [WIRED LAN]. 2) Press the button. ffThe [WIRED DETAILED SETUP] screen is displayed. 3) Press asqw to select an item, and change the setting according to the operation instruction of the menu. [DHCP] [IP ADDRESS] [SUBNET MASK] [DEFAULT GATEWAY] [DNS1] [DNS2] [EAP] [USER NAME] [PASSWORD] [ON] Select this item when there is a DHCP server in the network the projector is to be connected, and to acquire the IP address automatically. [OFF] Select this item when there is no DHCP server in the network the projector is to be connected, and to specify the IP address. Enter the IP address when [DHCP] is set to [OFF]. Enter the subnet mask when [DHCP] is set to [OFF]. Enter the default gateway address when [DHCP] is set to [OFF]. Enter the address of the preferred DNS server when [DHCP] is set to [OFF]. Enter the address of the alternate DNS server when [DHCP] is set to [OFF]. Select the EAP set for the RADIUS server. If the EAP is not set, set to [NONE]. The types of EAP that can be selected are as follows. [PEAP(MS-CHAPv2)], [PEAP(GTC)], [EAP-TTLS(MD5)], [EAP-TTLS(MS-CHAPv2)], [EAP-FAST(MSCHAPv2)], [EAP-FAST(GTC)], [EAP-TLS] Enter the user name to be used for authentication in single-byte alphanumeric characters (excluding the space). (Maximum of 64 characters) This can be set when [EAP] is set to anything other than [NONE]. Enter the password to be used for authentication in single-byte alphanumeric characters. (Maximum of 64 characters) This can be set when [EAP] is set to anything other than [NONE]. 4) Once the setting change is completed, press as to select [STORE], and press the button. ffThe confirmation screen is displayed. ffWhen [INVALID ENTRY. PLEASE RE-ENTER.] is displayed, change the setting to correct content. 5) Press qw to select [OK], and press the button. Note ff For setting content of each item, consult the network administrator. ff When using EAP, the projector is required to be set according to the RADIUS server setting. For the RADIUS server setting, confirm with the network administrator. ff Wired LAN and wireless LAN cannot be used in the same segment. ff When using the projector by setting [DHCP] to [ON], confirm that the DHCP server is operating. rrFactory default setting ffFollowing is preset as the factory default setting. ENGLISH - 141