Panasonic PT47WXD64J PT47WXD64 User Guide - Page 8

First Time Setup

Get Panasonic PT47WXD64J - 47inch PROJECTION TV PDF manuals and user guides View all Panasonic PT47WXD64J manuals
Add to My Manuals
Save this manual to your list of manuals

Page 8 highlights

ENGLISH FIRST TIME SETUP First Time Setup For your convenience, First Time Set up menu will be displayed on screen when the set is turned on for the first time. If needed, follow the menus and procedures displayed on-screen for setting up the features. Input Setup To select the configuration of RF input depending on the signal source. Note: No video will be displayed in this setup mode. Procedure • Press VOL to select Cable only, Cable/Antenna or Antenna only. • Press the OK button to underline your selection. First time setup OK Input Setup Cable only Auto Scan Manual Program Connect Cable to Antenna (A) Signal Meter Change your Input Setup and press OK • When the next screen is displayed, press OK button to start the Auto Scan. All available channels with a signal will be programmed into memory. Auto Scan This feature allows you to selectively auto scan channels. You can Scan All, Analog only channels or Analog & Digital channels. Procedure • Press OK button to start Auto Scan. First time setup SELECT Input Setup Scan All Auto Scan Antenna (A) Analog MENU to return EXIT Convergence Antenna (A) Analog & Digital Antenna (B) Analog Antenna (B) Analog & Digital • After Auto Scan is completed the PTV tunes to the first channel found during auto scan. Notes: • If the EXIT button is pressed at anytime during auto scan, the First Time Setup menu will be cancelled and the PTV will tune to analog channel 2 on ANTENNA (A). • If a CableCARD is present during the First Time Setup and Antenna (A) is set to cable, Antenna (A) will not be scanned due to the CableCARD providing the channel map. Convergence This menu lets you set the green CRT alignment and the center convergence. Follow the instructions on-screen to perform convergence. After convergence is performed, press EXIT to return to normal viewing. First time setup SELECT OK Input Setup Auto Scan Press OK to go to MENU to return EXIT Convergence Convergence setup 6 z

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
6
F
IRST
T
IME
S
ETUP
ENGLISH
First Time Setup
For your convenience, First Time Set up menu will be
displayed on screen when the set is turned on for the first
time. If needed, follow the menus and procedures
displayed on-screen for setting up the features.
Input Setup
To select the configuration of RF input depending on the
signal source.
Note:
No video will be displayed in this setup mode.
Procedure
•
Press
VOL
X
to select Cable only, Cable/Antenna or
Antenna only.
•
Press the
OK
button to underline your selection.
•
When the next screen is displayed, press
OK
button to
start the Auto Scan. All available channels with a signal
will be programmed into memory.
Auto Scan
This feature allows you to selectively auto scan channels.
You can Scan All, Analog only channels or Analog & Digital
channels.
Procedure
•
Press
OK
button to start Auto Scan.
•
After Auto Scan is completed the PTV tunes to the first
channel found during auto scan.
Notes:
•
If the EXIT button is pressed at anytime during auto
scan, the First Time Setup menu will be cancelled and
the PTV will tune to analog channel 2 on ANTENNA (A).
•
If a CableCARD is present during the First Time Setup
and Antenna (A) is set to cable, Antenna (A) will not be
scanned due to the CableCARD providing the channel
map.
Convergence
This menu lets you set the green CRT alignment and the center
convergence. Follow the instructions on-screen to perform
convergence. After convergence is performed, press
EXIT
to
return to normal viewing.
First time setup
Input Setup
Manual Program
Signal Meter
Auto Scan
OK
Cable only
W
W
Connect Cable to Antenna (A)
Change your Input Setup
and press OK
S
T
W
X
EXIT
MENU
to return
SELECT
First time setup
Convergence
Auto Scan
Input Setup
Scan All
Antenna (A) Analog
Antenna (A) Analog & Digital
Antenna (B) Analog
Antenna (B) Analog & Digital
First time setup
Convergence
Auto Scan
Input Setup
S
T
W
X
EXIT
MENU
to return
SELECT
OK
Press OK to go to
Convergence setup