Panasonic PTF200 Lcd Projector - Commercial Use

Panasonic PTF200 - LCD PROJECTOR - COMMERCIAL USE Manual

Get Panasonic PTF200 - LCD PROJECTOR - COMMERCIAL USE PDF manuals and user guides View all Panasonic PTF200 manuals
Add to My Manuals
Save this manual to your list of manuals

Panasonic PTF200 manual content summary:

  • Panasonic PTF200 | Lcd Projector - Commercial Use - Page 1
    Operating Instructions LCD Projector Commercial Use Model No. PT-F200NTU PT-F200U Before operating this product, please read the instructions carefully and save this manual for future use. TQBJ0248 ENGLISH
  • Panasonic PTF200 | Lcd Projector - Commercial Use - Page 2
    that you will be pleased with your Panasonic LCD projector. The serial number of your product may be found on its bottom. You should note it in the space provided below and retain this booklet in case service is required. Model number: PT-F200NTU / PT-F200U Serial number: WARNING: TO REDUCE THE
  • Panasonic PTF200 | Lcd Projector - Commercial Use - Page 3
    near the equipment and shall be easily accessible. Declaration of Conformity Model Number: PT-F200NTU / PT-F200U Trade Name: Panasonic Responsible party: Panasonic Corporation of North America Address: One Panasonic Way, Secaucus, New Jersey 07094 Telephone number: (888) 411 - 1996
  • Panasonic PTF200 | Lcd Projector - Commercial Use - Page 4
    installing 8 Cautions on use 9 Security 9 Accessories 9 Preparation Read this first 10 Minimum required setting screen 10 About Your Projector 11 Remote control 11 Projector body 12 Getting Started Setting up 14 Screen size and throw distance 14 Projection method 15 Front leg adjusters
  • Panasonic PTF200 | Lcd Projector - Commercial Use - Page 5
    Protections du support de montage au plafond 61 LAMP, TEMP and ARF Indicators 39 Managing the indicated problems 39 Care and Replacement 40 Cleaning the projector 40 Replacing the ARF (Auto Rolling Filter 40 Replacing the Lamp unit 41 Ceiling mount bracket safeguards 42 Troubleshooting 43
  • Panasonic PTF200 | Lcd Projector - Commercial Use - Page 6
    an Authorized Service Center for repairs. Do not attempt to repair the projector yourself, as this can be dangerous. Do not install this projector in use other than an authorized ceiling mount bracket. If foreign objects or water get inside the projector, or if the projector is dropped or the
  • Panasonic PTF200 | Lcd Projector - Commercial Use - Page 7
    replacing the lamp, be sure to disconnect the power plug from the wall socket. Electric shocks or explosions can result if this is not done. Do not allow infants or pets to touch the remote control unit. Keep the remote of the projector which is mounted in the ceiling. Do not set up the projector in
  • Panasonic PTF200 | Lcd Projector - Commercial Use - Page 8
    dealer about the replacement of the lamp unit and check the inside of the projector. Ask an Authorized Service Center to clean inside the projector at least once a year. If dust is left to build up inside the projector without being cleaned out, it can result in fire or problems with operation. It
  • Panasonic PTF200 | Lcd Projector - Commercial Use - Page 9
    . The Authorized Service Center will never ask you for the password. Do not share your password with anyone else. Accessories Make sure the following accessories are provided with your projector. Remote control for PT-F200NTU*1 (x1) N2QAYB000152 Remote control for PT-F200U*2 (x1) N2QAYB000154
  • Panasonic PTF200 | Lcd Projector - Commercial Use - Page 10
    F G I H buttons of the Remote control or Control panel on the projector to highlight the required language, and press Mounting in the ceiling and projecting from front Setting on a desk/floor and projecting from rear Mounting in the ceiling and projecting from rear ALTITUDE If you use the projector
  • Panasonic PTF200 | Lcd Projector - Commercial Use - Page 11
    Projector Remote to select. NETWORK button is only for PT-F200NTU. See CD-ROM contents. PAGE buttons are only for PT-F200NTU. See CD- Remote control. • Do not attempt to modify or disassemble the Remote control. Contact an Authorized Service Center for repairs. • Do not keep pressing the Remote
  • Panasonic PTF200 | Lcd Projector - Commercial Use - Page 12
    Projector Projector body J Top and front view Indicators POWER indicator (page 20) LAMP indicator (page 39) TEMP indicator (page 39) FILTER indicator (page 39) Remote input method. (page 22) COMPUTER1\COMPUTER2\S-VIDEO \VIDEO\COMPONENT\NETWORK\ COMPUTER1 MENU button Display the MAIN MENU. (page 27)
  • Panasonic PTF200 | Lcd Projector - Commercial Use - Page 13
    Filter) compartment (page 40) Font leg adjusters Screw up/down to adjust the projection angle. (page 15) About Your Projector Lamp projector. (page 20) LAN Connect a LAN cable for network connection. This terminal is PT-F200NTU terminal" on page 45. REMOTE See "REMOTE terminal" on page 47.
  • Panasonic PTF200 | Lcd Projector - Commercial Use - Page 14
    at a raised or a horizontally tilted position as it may cause malfunction of the projector. • Make sure the projector lens surface is parallel with the screen. You can tilt the projector body approximately ± 30° vertically. Overtilting may result in shortening the component's life. • For the
  • Panasonic PTF200 | Lcd Projector - Commercial Use - Page 15
    NOTE: • A translucent screen is required for rear projection. • When mounting the projector in the ceiling, the optional ceiling mount bracket (ET-PKF100H, ET-PKF100S) is required. • See "Ceiling mount bracket safeguards" on page 42. Front leg adjusters and throwing angle You can screw up/down
  • Panasonic PTF200 | Lcd Projector - Commercial Use - Page 16
    Lens shift lever to adjust the projected image position. 4. Screw the Lens shift lever clockwise to lock. Q Horizontal shift You can place the projector where the projector lens is up to 32% horizontally off-center from the screen and then adjust the image position with the Lens shift lever. Up to
  • Panasonic PTF200 | Lcd Projector - Commercial Use - Page 17
    when the Lens shift lever is at the horizontal limit of the shift range, you cannot move the lever to the horizontal limit. • When the projector is tilted and you adjust KEYSTONE, the center of the screen and the lens need to be realigned. • Do not attempt to pull the Lens
  • Panasonic PTF200 | Lcd Projector - Commercial Use - Page 18
    Before connection to the projector Read and follow the operating and connecting instructions of each peripheral device • See CD-ROM contents for the LAN network connection. J LAN terminal (PT-F200NTU only) ACT lamp (Green) Flashes when transmit data. LINK lamp (Yellow) Illuminates when a LAN cable is
  • Panasonic PTF200 | Lcd Projector - Commercial Use - Page 19
    Video player To video output or audio output Audio system DVD player NOTE: • When you connect more than one AV equipment, switch the audio connection manually. J Connecting with COMPONENT IN Video player To audio output DVD player Audio system ENGLISH - 19
  • Panasonic PTF200 | Lcd Projector - Commercial Use - Page 20
    indicator will not be lit. Network connection is ready while the POWER is turned off. (PT-F200NTU only) The POWER is switched on and the projector is getting ready to project. The projector is ready to project. The POWER is switched off and the projector is cooling the lamp. The POWER is switched on
  • Panasonic PTF200 | Lcd Projector - Commercial Use - Page 21
    flicker for the characteristics of the lamp. Those are normal and will not affect the performance of the projector. • When the internal cooling fan page 35. Switching off the projector Basic Operation 1. Open the Front panel cover. This is not necessary in Remote control operation. 2. Press the
  • Panasonic PTF200 | Lcd Projector - Commercial Use - Page 22
    the adjusted effect with the TEST PATTERN in OPTION menu. See "TEST PATTERN" on page 36. Focus lever Zoom lever 3. Adjust the angle of the projector. Screw down the Front leg adjusters and adjust the angle vertically. See "Front leg adjusters and throwing angle" on page 15. NOTE: • Do not touch
  • Panasonic PTF200 | Lcd Projector - Commercial Use - Page 23
    operation Operating range You can operate the projector with the Remote control within the remote range 15 m (49'2"), approximately ± 30° vertically and horizontally. Q Facing to the projector Ensure the Remote control emitter is facing to the Remote control signal receptor on front/back of
  • Panasonic PTF200 | Lcd Projector - Commercial Use - Page 24
    Basic Operation Remote control operation Switching the input signal You can switch the input method manually by pressing the COMPUTER, NETWORK (PT-F200NTU only) and VIDEO buttons. Press the required button several times or I H to cycle through the input methods as follows. The actual projected
  • Panasonic PTF200 | Lcd Projector - Commercial Use - Page 25
    sound will be stopped. Press the FREEZE button to return to the projection. NOTE: • Not available with NETWORK signals. Stopping the projection temporary You can turn off the lamp and stop the Press the SHUTTER button to return to the projection. projection temporary for electrical power save
  • Panasonic PTF200 | Lcd Projector - Commercial Use - Page 26
    Remote control operation Enlarging the centered area You can enlarge the projected image down to a centered area for emphasizing within the range of 1x to 2x. Q
  • Panasonic PTF200 | Lcd Projector - Commercial Use - Page 27
    which do not have their own dedicated buttons on the Remote control. The menu options are structured and categorized. You KEYSTONE POSITION POSITION LANGUAGE DOT CLOCK OPTION CLOCK PHASE SECURITY ASPECT 4:3 NETWORK RESIZING ON FRAME LOCK RETURN OFF SELECT ENTER 2. Press F G
  • Panasonic PTF200 | Lcd Projector - Commercial Use - Page 28
    page 30 page 30 page 31 page 32 page 32 page 32 page 32 page 32 page 33 page 33 Settings *1. Default setting for COMPUTER/NETWORK signals *2. Sub-menu items vary according to the selected input signal. ENGLISH - 28
  • Panasonic PTF200 | Lcd Projector - Commercial Use - Page 29
    menu Sub-menu OPTION INPUT GUIDE STARTUP LOGO COMPUTER2 SELECT FILTER REMAINING LAMP RUNTIME POWER OFF TIMER DIRECT POWER ON CONTROL PANEL AUTO SETUP SIGNAL SEARCH INSTALLATION ALTITUDE CLOSED CAPTION SETTING TEST PATTERN DETAILED SETUP SECURITY NETWORK (PT-F200NTU only. See CDROM contents
  • Panasonic PTF200 | Lcd Projector - Commercial Use - Page 30
    PICTURE menu Remote control Control panel COLOR You can adjust the color saturation ON: Active OFF: Deactive NOTE: • Do not cover the ALS (Ambient Luminance Sensor) of the projector. See "ALS (Ambient Luminance Sensor)" on page 12. • AUTO is not available when INSTALLATION setting
  • Panasonic PTF200 | Lcd Projector - Commercial Use - Page 31
    . J For S-VIDEO/VIDEO signals Q TV-SYSTEM When the video signal is changed, the setting switches automatically. You can switch the setting manually to match the video data. Press I H to cycle through the options. AUTO NTSC SECAM NTSC 4.43 PAL-N PAL PAL-M NOTE: • AUTO setting will select
  • Panasonic PTF200 | Lcd Projector - Commercial Use - Page 32
    menu Remote control . (Available with signals from COMPUTER only) KEYSTONE If the projector is aligned non-perpendicularly to the screen, or if the projection may not make a difference. ASPECT You can switch the aspect ratio manually when needed. Press I H to cycle through the options. 4:3 16
  • Panasonic PTF200 | Lcd Projector - Commercial Use - Page 33
    RESIZING is set to OFF; • The size of the image will be projected smaller and you may need to adjust ZOOM and FOCUS, or the projector position backwards and forwards. • DIGITAL ZOOM, KEYSTONE and INDEX-WINDOW are not available. Q AUTO The S1 signal which contains an identifying signal will be
  • Panasonic PTF200 | Lcd Projector - Commercial Use - Page 34
    on page 40. • After you replace the ARF, FILTER REMAINING should be reset to "0" by pressing the ENTER button for 3 seconds. LAMP RUNTIME You can check how long the lamp has been used. NOTE: • LAMP RUNTIME is a relevant matter for lamp replacement timing. See "Replacing the Lamp unit" on page 41
  • Panasonic PTF200 | Lcd Projector - Commercial Use - Page 35
    Setting on a desk/floor and projecting from front Mounting in the ceiling and projecting from front Setting on a desk/floor and projecting from rear Mounting in the ceiling and projecting from rear ALTITUDE If you use the projector at high elevation, the ALTITUDE setting need to be HIGH to
  • Panasonic PTF200 | Lcd Projector - Commercial Use - Page 36
    the right side J INITIALIZE ALL You can reset all of the customized settings to the factory defaults except NETWORK, LAMP RUNTIME and FILTER REMAINING menu settings. 1. Press the ENTER button 2. Turn off the projector by pressing the POWER button. 3. Switch off the MAIN POWER button to reset the
  • Panasonic PTF200 | Lcd Projector - Commercial Use - Page 37
    SECURITY menu Remote control Control panel See "Navigating through the MENU" on page 27. See INPUT PASSWORD OFF POSITION PASSWORD CHANGE LANGUAGE TEXT DISPLAY OFF OPTION TEXT CHANGE SECURITY NETWORK SELECT RETURN PASSWORD ENTER When you apply to the SECURITY menu before you change
  • Panasonic PTF200 | Lcd Projector - Commercial Use - Page 38
    " on page 28. NOTE: • The NETWORK menu is available only with PT-F200NTU. • See the PJ Link or network information in the contents of the CD-ROM which is provided with the projector. Items in NETWORK menu In NETWORK menu, the following items are available. WIRED LAN WIRELESS LAN NAME CHANGE INPUT
  • Panasonic PTF200 | Lcd Projector - Commercial Use - Page 39
    /or FILTER indicators will inform you. Manage the indicated problems as follow. 1. Confirm the status of all indicators and projector, and switch off the projector in proper way. 2. Find out the cause of the problem by status of the LAMP, TEMP and/or FILTER indicators. 3. Follow the instruction for
  • Panasonic PTF200 | Lcd Projector - Commercial Use - Page 40
    projector. If you use a chemical treated wipe, follow the instructions supplied driver. Contact an Authorized Service Centre to purchase a replacement ARF (ET-RFF100). J When to replace the ARF ARF is consumable product and effects on ventilation. FILTER indicator will inform you of the replacement
  • Panasonic PTF200 | Lcd Projector - Commercial Use - Page 41
    -head screwdriver. Contact an Authorized Service Center to purchase a replacement Lamp unit (ET-LAF100). When the projector is mounted in the ceiling, do not work directly under the projector or put your face closer to the projector. NOTE: • Prior to replacing the lamp unit, allow it to cool
  • Panasonic PTF200 | Lcd Projector - Commercial Use - Page 42
    Install the ceiling mount bracket according to the installation instructions. 2. Loop the security cable around the ceiling mount bracket with less slack. Lace the cable of the end with a latch through the loop on the other end of the cable. 3. Attach the latch on to the bottom of the projector with
  • Panasonic PTF200 | Lcd Projector - Commercial Use - Page 43
    Troubleshooting Should any problem persist, contact your dealer. Problem Cause Power does not turn on. No picture appears. The picture is fuzzy. The color is pale or greyish. No sound can be heard from the internal speaker. The control buttons of the projector do not operate. The Remote control
  • Panasonic PTF200 | Lcd Projector - Commercial Use - Page 44
    Technical Information List of compatible signals Mode Display resolution (dots)*1 Scanning frequency H (kHz) V (Hz) Dot clock frequency (MHz) Picture quality*2 Terminals NTSC/NTSC 4.43/ PAL-M/PAL60 PAL/PAL-N/SECAM 480i 576i 480p 576p 1 080/60i 1 080/50i 720/60p*4 720/50p VESA VGA480 SVGA MAC
  • Panasonic PTF200 | Lcd Projector - Commercial Use - Page 45
    the connector panel of the projector conforms to the RS-232C interface specification, so that the projector can be controlled by a personal ETX. You can add the required parameter. The projector can not receive any command for 10 seconds after the lamp is switched on. Wait 10 seconds before sending
  • Panasonic PTF200 | Lcd Projector - Commercial Use - Page 46
    S-VIDEO RG2 = COMPUTER2 NWP = NETWORK (PT-F200NTU only) Call back 0 = Standby 1 = Lamp ON control active 2 = Lamp ON 3 = Lamp OFF control active Turning off the while the INPUT GUIDE is set to DETAILED, the computer connection guidance will be displayed. Manufacturer Panasonic NEC Key command
  • Panasonic PTF200 | Lcd Projector - Commercial Use - Page 47
    COMPUTER2 COMPONENT VIDEO Short Short Open S-VIDEO Open Short Short NETWORK (PT-F200NTU only) NOTE: • When pin A and pin I are short-circuited, the buttons on the projector's control panel, POWER and INPUT SELECT buttons on the Remote control cannot be used. In addition, the RS-232C commands
  • Panasonic PTF200 | Lcd Projector - Commercial Use - Page 48
    LCD panel Display method 3 transparent LCD panels (RGB) Drive method Active matrix method Lens Lamp Pixels 786 432 (1 024 x 768) x 3 panels Manual zoom (2x)/Manual focus F 1.7 - 2.6, f 21.6 mm - 43.0 mm UHM lamp : 3 FRONT/DESK, FRONT/CEILING, REAR/DESK, REAR/CEILING (Menu selection method) 1
  • Panasonic PTF200 | Lcd Projector - Commercial Use - Page 49
    V [rms] (variable) SERIAL D-sub 9-pin RS-232C compatible REMOTE D-sub 9-pin For external control LAN (RJ-45) (PT-F200NTU only) Single - line, For network connection 10 Base-T/100Base-TX/1000Base-T Wireless LAN (PT-F200NTU only) Compatible Wireless channel Distance IEEE802.11b/IEEE802.11g
  • Panasonic PTF200 | Lcd Projector - Commercial Use - Page 50
    Technical Information Screen size and throw distance for 16:9 aspect ratio Projection size (16 : 9) Throw distance (L) Screen Diagonal (SD) Screen height (SH) Screen width (SW) Minimum distance (LW) Maximum distance (LT) (0.84 m) 33" 0.41 m (1'4") 0.73 m (2'4") 2.1 m (6'10") (1.02 m) 40
  • Panasonic PTF200 | Lcd Projector - Commercial Use - Page 51
    bitmap font, which is manufactured and sold by Ricoh Company, Ltd. All other trademarks are the property of the various trademark owners. Appendix These Operating Instructions are printed on recycled paper. ENGLISH - 51
  • Panasonic PTF200 | Lcd Projector - Commercial Use - Page 52
    ALL 36 INPUT GUIDE 34 INPUT PASSWORD 37 INPUT SELECT Control panel button 12 Remote control button 11 Selecting 22, 24 INSTALLATION Menu 35 Projection method 15 K KEYSTONE 32 L LAMP Indicator 12 Indicator status 39 LAMP RUNTIME 34 Lamp unit compartment 13 Replacing 41 LAN 13
  • Panasonic PTF200 | Lcd Projector - Commercial Use - Page 53
    45 SHARPNESS 30 SHUTTER Remote control 25 Remote control button 11 SIGNAL SEARCH 35 Speaker 12 Specifications 48 STARTUP LOGO 34 Troubleshooting 43 TV-SYSTEM 31 V VARIABLE AUDIO OUT 13 VIDEO Remote control 24 Remote control button 11 VIDEO IN 13 VOLUME 36 Remote control 26 Remote
  • Panasonic PTF200 | Lcd Projector - Commercial Use - Page 54
    vous serez satisfait de votre projecteur LCD Panasonic. Le numéro de série de votre produit se trouve sous le projecteur. Veuillez le noter dans l'espace ci-dessous prévu à cet effet et conserver cette notice en cas de maintenance requise. Numéro de modèle: PT-F200NTU / PT-F200U Numéro de série
  • Panasonic PTF200 | Lcd Projector - Commercial Use - Page 55
    et s'il n'est pas installé et utilisé conformément aux instructions fournies avec celuici, peut provoquer des interférences nuisibles aux communications PT-F200NTU / PT-F200U Désignation commerciale:Panasonic Fabricant responsable: Panasonic Corporation of North America Adresse: One Panasonic
  • Panasonic PTF200 | Lcd Projector - Commercial Use - Page 56
    s'il est installé au plafond. Si l'installation n'est pas faite correctement, cela peut entraîner des blessures ou des chocs électriques. Ne pas utiliser un support de montage au plafond qui n'est pas agréé. Si de l'eau ou des objets étrangers pénètrent dans le projecteur, si le projecteur tombe, ou
  • Panasonic PTF200 | Lcd Projector - Commercial Use - Page 57
    la laisse tomber et des blessures et des mauvais fonctionnements peuvent s'ensuivre. Lors du remplacement de la lampe, la laisser refroidir pendant au moins une heure avant de la manipuler. Le couvercle de la lampe devient très chaud, et on risque de se brûler si on le touche. Avant de remplacer
  • Panasonic PTF200 | Lcd Projector - Commercial Use - Page 58
    la télécommande pendant une longue période, cela risque de provoquer des fuites, une hausse anormale de la température interne ou une explosion. Si la lampe s'est cassée, ventiler immédiatement la pièce. Ne pas toucher ni approcher le visage des morceaux cassés. Le non respect de cette consigne peut
  • Panasonic PTF200 | Lcd Projector - Commercial Use - Page 59
    uniquement par un technicien qualifié. Voir « Protections du support de montage au plafond » à la page 44 peut raccourcir la durée de vie de la lampe ou d'autres composants. Précautions lors de ceci n'affecte pas le bon fonctionnement de votre LCD. Écran N'appliquer aucun produit volatil qui risque
  • Panasonic PTF200 | Lcd Projector - Commercial Use - Page 60
    un tournevis cruciforme. Contacter un centre de service aprés-vente agréé pour acheter une L'Unité de la lampe (ET-LAF100) de rechange. En cas la lampe, telles que la durée de garantie, se reporter aux instructions fournies avec l'Unité de la lampe. • Lorsque la durée d'utilisation de la lampe dé
  • Panasonic PTF200 | Lcd Projector - Commercial Use - Page 61
    de fixation de l'Unité de la lampe Appuyer ici 8. Fixer le Couvercle de la lampe puis resserrer les 2 vis du Couvercle de la lampe à l'aide du tournevis cruciforme. Protections du support de montage au plafond Bien que le projecteur ainsi que le support d'installation au plafond aient été conçus
  • Panasonic PTF200 | Lcd Projector - Commercial Use - Page 62
    handling may apply. See www.dtsc.ca.gov/hazardouswaste/perchlorate. Projectors Panasonic Projector Systems Company Unit of Panasonic Corporation of North America One Panasonic Way, Secaucus, NJ 07094 (201) 392 - 6591 Technical Support: (888) 411 - 1996 FAX: (201) 348 - 7523 E-Mail: projectorsupport
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
E
NGLISH
Operating Instructions
LCD Projector
Model No.
PT-F200NTU
PT-F200U
Before operating this product, please read the instructions carefully and save this manual for future use.
TQBJ0248
Commercial Use