Panasonic PTF200 Lcd Projector - Commercial Use - Page 20

Switching the projector on/off, Power cord, POWER indicator

Get Panasonic PTF200 - LCD PROJECTOR - COMMERCIAL USE PDF manuals and user guides View all Panasonic PTF200 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 20 highlights

Switching the projector on/off Power cord J Connecting 1. Make sure the shape of the power cord and the AC IN connector on the back of the projector match, then push the plug all the way in. 2. Connect the Mains lead to a wall socket. J Disconnecting 1. Make sure the MAIN POWER is switched off and unplug the Mains lead from the wall socket. 2. Hold the plug and unplug the Mains lead from the AC IN connector on the back of the projector. J Direct power off function You can disconnect the Mains lead from the projector or switch off the MAIN POWER button while projecting or soon after projecting. The internal lamp cooling fan will keep operating by the internal power supply. NOTE: • If the projector is switched on again while the internal cooling fan is still operating by the internal power supply, it may take a while to start the projection. J Direct power on function If you activate the DIRECT POWER ON, you can start the projection only with connecting the Mains lead or switching on the MAIN POWER. See "DIRECT POWER ON" on page 35. NOTE: • Do not use other than a provided Mains lead. • Ensure all the input devices are connected and turned off before connecting the Mains lead. • Do not force the connector as this may damage the projector and/or the power cord. • Dirt or dust build-up around plugs may cause fire or electrical hazards. • Switch off the power to the projector when not in use. POWER indicator POWER indicator Basic Operation Indicator status No illumination or flashing RED GREEN ORANGE Lit Flashing Flashing Lit Lit Flashing Status The MAIN POWER is switched off. The MAIN POWER is switched on and the projector is in standby. When the LAMP or TEMP indicator is flashing, the POWER indicator will not be lit. Network connection is ready while the POWER is turned off. (PT-F200NTU only) The POWER is switched on and the projector is getting ready to project. The projector is ready to project. The POWER is switched off and the projector is cooling the lamp. The POWER is switched on again when cooling the lamp and recovering to projection mode. Recovery may take a while. NOTE: • If the projector is switched on again while the internal cooling fan is still operating by the internal power supply, it may take a while to start the projection. • The electric consumption in standby mode is 3.5 W. ENGLISH - 20

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
E
NGLISH - 20
Basic Operation
Switching the projector on/off
Connecting
1.
Make sure the shape
of the power cord and
the
AC IN
connector
on the back of the
projector match, then
push the plug all the way in.
2.
Connect the
Mains lead
to a wall socket.
Disconnecting
1.
Make sure the
MAIN POWER
is switched off and
unplug the
Mains lead
from the wall socket.
2.
Hold the plug and unplug the
Mains lead
from the
AC IN
connector on the back of the projector.
Direct power off function
You can disconnect the
Mains lead
from the
projector or switch off the
MAIN POWER
button
while projecting or soon after projecting. The
internal lamp cooling fan will keep operating by the
internal power supply.
Direct power on function
If you activate the
DIRECT POWER ON
, you can
start the projection only with connecting the
Mains
lead
or switching on the
MAIN POWER
. See
“DIRECT POWER ON” on page 35.
Power cord
NOTE:
•
If the projector is switched on again while the internal
cooling fan is still operating by the internal power
supply, it may take a while to start the projection.
NOTE:
•
Do not use other than a provided
Mains lead
.
•
Ensure all the input devices are connected and turned off before connecting the
Mains lead
.
•
Do not force the connector as this may damage the projector and/or the power cord.
•
Dirt or dust build-up around plugs may cause fire or electrical hazards.
•
Switch off the power to the projector when not in use.
POWER indicator
Indicator status
Status
No illumination or flashing
The
MAIN POWER
is switched off.
RED
Lit
The
MAIN POWER
is switched on and the projector is in standby.
When the
LAMP
or
TEMP
indicator is flashing, the
POWER
indicator will
not be lit.
Flashing
Network connection is ready while the
POWER
is turned off.
(PT-F200NTU only)
GREEN
Flashing
The
POWER
is switched on and the projector is getting ready to project.
Lit
The projector is ready to project.
ORANGE
Lit
The
POWER
is switched off and the projector is cooling the lamp.
Flashing
The
POWER
is switched on again when cooling the lamp and recovering
to projection mode. Recovery may take a while.
NOTE:
•
If the projector is switched on again while the internal cooling fan is still operating by the internal power supply, it may take
a while to start the projection.
•
The electric consumption in standby mode is 3.5 W.
POWER
indicator