Panasonic RX-D550 Owners Manual - Page 15

Bluetooth® Pairing cannot be completed. ≥ Check the Bluetooth® device condition. The device cannot be connected. ≥ The pairing of the device was unsuccessful or the registration has been replaced. Try re-pairing the device. (l 8) ≥ This unit might be connected to a different device. Disconnect the other device and try re-pairing the device. (l 8) ≥ If "MODE 2" is selected in "LINK MODE", select "MODE 1". (l 8) ≥ If the problem persists, turn the unit off and on, then try again. The device is connected, but audio cannot be heard through this unit. ≥ For some built-in Bluetooth® devices, you have to set the audio output to "RX-D550" manually. Read the operating instructions for the device for details. The sound is interrupted. ≥ The device is out of the 10 m (33 ft) communication range. Place the Bluetooth® device closer to this unit. ≥ Remove any interference between this unit and the device. ≥ Other devices that use the 2.4 GHz frequency band, such as wireless routers, microwaves, cordless phones, etc. are interfering. Place the Bluetooth® device closer to this unit and distance it from the other devices. ≥ Select "MODE 1" for stable communication. (l 8) Messages The following messages or service numbers may appear on the unit's display. "--:--" ≥ You plugged the AC power supply cord in for the first time or there was a power failure recently. Set the time (l 11). "ADJUST CLOCK" ≥ Clock is not set. Adjust the clock accordingly. "ADJUST TIMER" ≥ Play timer is not set. Adjust the play timer accordingly. "AUTO OFF" ≥ The unit has been left unused for about 20 minutes and will shut down within a minute. Press any button to cancel it. "ERROR" ≥ Incorrect operation is performed. Read the instructions and try again. "F" / "F stands for a number.) ≥ There is a problem with this unit. Disconnect the AC power supply cord from the AC outlet, reconnect it to the outlet after about 30 seconds. Wait for about 10 seconds, then turn on the unit. If the problem still persists, disconnect the AC power supply cord and consult your dealer. "LINKING" ≥ This system is trying to connect to the last connected Bluetooth® device when "BLUETOOTH" is selected. "NO DEV" ≥ The USB device is not inserted correctly. Read the instructions and try again (l 7). "NO DISC" ≥ Insert the disc to be played (l 7). "NO PLAY" ≥ Examine the content. You can only play supported format. (l 16) ≥ The files in the USB device can be corrupted. Format the USB device and try again. ≥ The unit may have a problem. Turn the unit off and then on again. "NOT SUPPORTED" ≥ You have connected an unsupported USB device. "PLAY ERROR" ≥ You played an unsupported file. The system will skip that track and play the next one. "READING" ≥ The unit is checking the "CD"/"USB" information. After this display has disappeared, start operating. "REMOTE stands for a number.) ≥ The remote control and this unit are using different codes. Change the code on the remote control. - When "REMOTE 1" is displayed, press and hold [OK] and [ ] on the remote control for at least 4 seconds. - When "REMOTE 2" is displayed, press and hold [OK] and [O SELECT] on the remote control for at least 4 seconds. "USB OVER CURRENT ERROR" ≥ The USB device is drawing too much power. Disconnect the USB device, turn the unit off and then on again. ≥ Check the connection, it may be caused by a faulty USB cable. "VBR" ≥ The system cannot show the remaining play time for variable bit rate (VBR) tracks. "WAIT" ≥ This is displayed, for example, when this unit is turning off. - 15 -