Panasonic SC-PMX90 Owners Manual - Page 16
Specifications
View all Panasonic SC-PMX90 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 16 highlights
TQBM0360 "DEVICE NO RESPONSE" "HUB NOT SUPPORTED" "NOT SUPPORTED" • You have connected an unsupported USB device. "OPT UNLOCKED" • "OPT" is selected, but no device is connected. • The sampling frequency components, etc. of the audio signals are not input correctly. - For supported formats, refer to "Connecting to OPT IN (Optical Audio In) terminal" (@ 5). "PC UNLOCKED" • "PC" is selected, but a PC is not connected. "PGM FULL" • The number of programed tracks is more than 24. "PLAYERROR" • You played an unsupported file. The system will skip that track and play the next one. "READING" • The unit is checking the CD information. After this display has disappeared, start operating. • When starting playback of DSD files, it may take time to read the file. Wait until reading completes. "REMOTE stands for a number.) • The remote control and this unit are using different codes. Change the code on the remote control. - When "REMOTE 1" is displayed, press and hold [OK] and [1] for at least 4 seconds. - When "REMOTE 2" is displayed, press and hold [OK] and [2] for at least 4 seconds. "USB OVER CURRENT ERROR" • The USB device is drawing too much power. Remove the USB device. Switch the system off and on again. "VBR" • The system cannot show the remaining play time for variable bit rate (VBR) tracks. "WAIT" • This is displayed, for example, when this unit is turning off. 16 Memory reset (initialization) Reset the memory when the following situations occur: • There is no response when buttons are pressed. • You want to clear and reset the memory contents. 1 Disconnect the AC power supply cord. Wait 30 seconds before you continue with step 2. 2 While you press and hold [Í/I] on the main unit, connect the AC power supply cord again. Keep holding down [Í/I] until appears on the display. 3 Release [Í/I]. All the settings are set back to the factory default. It is necessary to set the memory items again. Remote control code When other Panasonic equipment responds to the remote control of this system, change the remote control code for this system. To set the code to "REMOTE 2" 1 Press [SELECTOR] on the main unit to select "CD". 2 Press and hold [∫] on the main unit and [2] on the remote control until "REMOTE 2" is shown. 3 Press and hold [OK] and [2] for a minimum of 4 seconds. • The factory default is "REMOTE 1". • To change the mode back to "REMOTE 1", repeat the steps above but replace the button pressed on the remote control from [2] to [1]. Specifications General Power supply AC 120 V, 60 Hz Power consumption 40 W Dimensions (main unit) (W k H k D) 211 mm k 114 mm k 267 mm (8 5/16qk4 1/2qk10 1/2q) Mass (main unit) Approx. 2.8 kg (6.2 lbs) Operating temperature range 0 °C to +40 °C (r32 oF to r104 oF) Operating humidity range 35 % to 80 % RH (no condensation) Power consumption in standby mode*1, 2 0.25 W (approx.) (When "BLUETOOTH STANDBY" is "ON")*2 0.35 W (approx.) *1: "BLUETOOTH STANDBY" is "OFF". *2: No device is connected to the USB port before turning to standby mode. Amplifier section RMS output power Front Ch (both ch driven) 60 W per channel (3 ™), 1 kHz, 10% THD Total RMS power 120 W FM section Preset memory 30 stations Frequency range 87.9 MHz to 107.9 MHz (200 kHz step) 87.5 MHz to 108.0 MHz (100 kHz step) Antenna terminals 75 ™ (unbalanced) Disc section Disc played (8 cm (3q) or 12 cm (5q)) CD, CD-R/RW (CD-DA, MP3*3) Pick up Wavelength 790 nm (CD) *3: MPEG-1 Layer 3, MPEG-2 Layer 3