Panasonic SC-PTX7 Dvd Home Theater Sound System - Page 100
Troubleshooting guide - replacement speaker
UPC - 037988254873
View all Panasonic SC-PTX7 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 100 highlights
Troubleshooting guide Before requesting service, make the following checks. If you are in doubt about some of the check points, or if the solutions indicated in the chart do not solve the problem, refer to "Customer Services Directory" on page 110 if you reside in the U.S.A., or refer to "Product information" on page 109 if you reside in Canada. General Issues Power Page No power. ≥Insert the AC power supply cord securely into the household AC outlet. 13 The unit is automatically ≥When "Auto Power Off Mode" is set to "On", the unit automatically switches to 93 switched to the standby standby after approximately 10 minutes in the stop mode. mode. When the AC power supply ≥Last time you used the unit, was the cord removed from the power outlet 29, cord is plugged in, "- - - -" immediately after the unit was turned off, or while "- - - -" was flashing on the unit 32 flashes on the unit display. display? Conversion and analysis was aborted while the unit was in standby mode. The unit is converting and analyzing the tracks again. While "- - - -" is flashing on the unit display, the unit can be turned on without any problems. The unit display does not ≥If there are recorded tracks that have not been converted or analyzed yet, the unit 32, turn off even when the unit is will enter standby in "Quick-Start Mode" when the unit is turned off. Once 93 in "Power-Save Mode". conversion and analysis is complete, the unit will switch to "Power-Save Mode". The unit starts up slower ≥When the number of tracks recorded to the HDD increases, it will take more time - than it used to when set to for the unit to start up. "Power-Save Mode". I set the unit to "Quick-Start ≥In some cases, the unit manages the system for stable operation for several tens of - Mode", but it starts up slow. seconds while the unit is turned off. During this period, if the unit is turned on, it can take time to start up ("Starting now. Please wait" is displayed). Furthermore, during system management, the standby indicator (red) will turn off briefly and a "click" sound may be heard. General Issues Operation 100 RQT8926 The main unit is hot. The display is dim. No response when any buttons pressed. No response when remote control buttons pressed. When using the remote control, the message "Please set your remote control to Mode 1 (or 2)." is displayed. Using remote controls for other devices causes accidental operation on this unit. No on-screen display. No picture or sound. Audio does not sound correct. The left and right channels are reversed. ≥When this unit is used for an extended period of time, the main unit can become hot. However, this does not cause any harm to the unit. ≥Change "FL Dimmer" in "Power On/Off" menu. ≥This unit cannot play discs other than the ones listed in these operating instructions. ≥The unit may not be operating properly due to lightning, static electricity, or other external factors. Turn the unit off and on again. Alternatively, turn the unit off, disconnect the AC power supply cord, and then reconnect it. ≥Condensation has formed: Wait 1 to 2 hours for it to evaporate. ≥Have you created a backup or restored the HDD? Backup and restore can take some time to complete. ≥Press and hold [Í/I] on the main unit for approximately 10 seconds to force the unit to restart. ≥Check that the batteries are installed correctly. ≥The batteries are depleted: Replace them with new ones. ≥Point the remote control at the remote control signal sensor and operate. ≥The remote control settings are not correctly set with this unit's settings. Change the mode on the remote control. ≥Are you using other Panasonic products at the same time? The remote control signals may be similar, so change the remote control mode. ≥Select "On" in "On-Screen Messages" in "Display" menu. ≥Check the video or audio connection. ≥Check the power or input setting of the connected equipment. ≥Check that the disc has something recorded on it. ≥Are the left and right cords connecting the speakers or the external device reversed? Check the cord for the speakers and the external device and connect them correctly. ≥Are the left and right speakers properly installed? Look on the bottom of the speakers to identify the left and right speakers. - 93 24 - - - - 8 8 8 22 22 93 12, 13, 17, 18 - - 12, 17, 18 10