Panasonic Toughbook FZ-G1 Operating Instructions - Page 29

Touch [Exit] and double-touch [Save Values and Reboot].

Get Panasonic Toughbook FZ-G1 PDF manuals and user guides View all Panasonic Toughbook FZ-G1 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 29 highlights

Useful Information 2 Perform the "First-time Operation" ( page 19). NOTE l The date and time, and the time zone may not be correct. Be sure to set them correctly. 3 Perform Windows Update. 4 Clear TPM. A On the Start screen, flick from bottom side to inside of the screen and touch [All apps] on the toolbar. B Touch [Run] under "Windows System", input [tpm.msc] and touch [OK]. C Touch [Clear TPM ...] under "Actions" on the right of the "TPM Manager on Local Com- puter" screen. D Touch [Restart] of the "Manage the TPM security hardware" screen. The computer will restart. E When "TPM configuration change was requested to ..." is displayed, press F12. Windows will start. F When "TPM is ready" appears, touch [Close]. 1 Turn on the computer, and touch the top left corner of the screen several times while [Panasonic] boot screen is displayed. The Setup Utility starts up. l If the [Panasonic] boot screen is not displayed, turn on the computer while touching the top left corner of the screen. l If the password is requested, enter the Supervisor Password. 2 Write down all of the contents of the Setup Utility and touch [Exit] and double-touch [Load Default Values]. At the confirmation message, touch [Yes]. 3 Touch [Exit] and double-touch [Save Values and Reboot]. At the confirmation message, touch [Yes]. Computer will restart. 4 Touch the top left corner of the screen several times while [Panasonic] boot screen is displayed. The Setup Utility starts up. l If the password is requested, enter the Supervisor Password. 5 Select the [Exit] menu, then double-touch [Recovery Partition]. 6 Touch [Reinstall Windows] and touch [Next]. The License Agreement screen appears. 7 Touch [YES]. The License Agreement screen appears. 8 Touch [Yes, I agree to the provisions above and wish to continue!] and touch [Next]. 9 Select the setting and touch [Next]. l [Reinstall Windows to the whole Hard Disk to factory default.] Select this option when you want to install Windows to the factory default. After installation, you can create a new partition. For how to create a new partition, refer to "To change the partition structure" ( page 21). 29

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
29
Useful Information
2
Perform the “First-time Operation” (
è
page 19).
NOTE
l
The date and time, and the time zone may not be correct. Be sure to set them correctly.
3
Perform Windows Update.
4
<Only for model with TPM> Clear TPM.
A
On the Start screen, flick from bottom side to inside of the screen and touch [All apps]
on the toolbar.
B
Touch [Run] under “Windows System”, input [tpm.msc] and touch [OK].
C
Touch [Clear TPM ...] under “Actions” on the right of the “TPM Manager on Local Com-
puter” screen.
D
Touch [Restart] of the “Manage the TPM security hardware” screen.
The computer will restart.
E
When “TPM configuration change was requested to ...” is displayed, press
F12
.
Windows will start.
F
When “TPM is ready” appears, touch [Close].
1
Turn on the computer, and touch the top left corner of the screen sev-
eral times while [Panasonic] boot screen is displayed.
The Setup Utility starts up.
l
If the [Panasonic] boot screen is not displayed, turn on the computer while touching the
top left corner of the screen.
l
If the password is requested, enter the Supervisor Password.
2
Write down all of the contents of the Setup Utility and touch [Exit] and
double-touch [Load Default Values]
.
At the confirmation message, touch [Yes].
3
Touch [Exit] and double-touch [Save Values and Reboot].
At the confirmation message, touch [Yes].
Computer will restart.
4
Touch the top left corner of the screen several times while [Panasonic]
boot screen is displayed.
The Setup Utility starts up.
l
If the password is requested, enter the Supervisor Password.
5
Select the [Exit] menu, then double-touch [Recovery Partition].
6
Touch [Reinstall Windows] and touch [Next].
The License Agreement screen appears.
7
Touch [YES].
The License Agreement screen appears.
8
Touch [Yes, I agree to the provisions above and wish to continue!] and
touch [Next].
9
Select the setting and touch [Next].
l
[Reinstall Windows to the whole Hard Disk to factory default.]
S
elect this option when you want to install Windows to the factory default. After instal-
lation, you can create a new partition. For how to create a new partition, refer to “To
change the partition structure”
(
è
page 21).