Panasonic Toughbook FZ-G1 Operating Instructions - Page 31

Check the [UEFI Boot] setting of the Setup Utility.

Get Panasonic Toughbook FZ-G1 PDF manuals and user guides View all Panasonic Toughbook FZ-G1 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 31 highlights

1 Connect the DVD drive to the USB port. 2 Start the Setup Utility. A Display "Charm" and touch - [Change PC settings] - [General]. B Touch [Restart now] under "Advanced startup". C Touch [Troubleshoot] - [Advanced options] - [UEFI Firmware Settings] - [Restart]. Turn on the computer, and touch top left of the screen while [Panasonic] boot screen is displayed. l If the [Panasonic] boot screen is not displayed, turn on the computer while touching top left of the screen. l If the password is requested, enter the Supervisor Password. 3 Write down all of the contents of the Setup Utility and touch [Exit] and double-touch [Load Default Values]. At the confirmation message, touch [Yes]. 4 Check the [UEFI Boot] setting of the Setup Utility. [UEFI Boot] should be set to as follows. When the recovery disc for Windows 8 is used: [Enabled] When the recovery disc for Windows 7 is used: [Disabled] 5 Set the Recovery Disc into the DVD drive. 6 Touch [Exit] and double-touch [Save Values and Reboot]. At the confirmation message, touch [Yes]. Computer will restart. 7 Touch top left of the screen while [Panasonic] boot screen is displayed. The Setup Utility starts up. l If the password is requested, enter the Supervisor Password. 8 Touch [Exit], then double-touch your DVD drive in [Boot Override]. 9 Double-touch [Yes]. The computer will restart. 10 Touch [Reinstall Windows] and touch [Next]. 11 At the confirmation message, touch [YES]. 12 At the License Agreement screen, Touch [Yes, I agree to the provisions above and wish to continue!] and touch [Next]. 13 When the recovery disc for Windows 8 is used, touch [Next]. When the recovery disc for Windows 7 is used, select the setting and touch [Next]. l [Reinstall Windows to the whole Hard Disk to factory default.] Select this option when you want to install Windows to the factory default. After installation, you can create a new partition. For how to create a new partition, refer to "To change the partition structure" ( page 21). Useful Information 31

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
31
Useful Information
1
Connect the DVD drive to the USB port.
2
Start the Setup Utility.
A
Display “Charm” and touch
- [Change PC settings] - [General].
B
Touch [Restart now] under “Advanced startup”.
C
Touch [Troubleshoot] - [Advanced options] - [UEFI Firmware Settings] - [Restart].
Turn on the computer, and touch top left of the screen while [Panasonic] boot screen is
displayed.
l
If the [Panasonic] boot screen is not displayed, turn on the computer while touching top
left of the screen.
l
If the password is requested, enter the Supervisor Password.
3
Write down all of the contents of the Setup Utility and touch [Exit] and
double-touch [Load Default Values].
At the confirmation message, touch [Yes].
4
Check the [UEFI Boot] setting of the Setup Utility.
[UEFI Boot] should be set to as follows.
When the recovery disc for Windows 8 is used: [Enabled]
When the recovery disc for Windows 7 is used: [Disabled]
5
Set the Recovery Disc into the DVD drive.
6
Touch [Exit] and double-touch [Save Values and Reboot].
At the confirmation message, touch [Yes].
Computer will restart.
7
Touch top left of the screen while [Panasonic] boot screen is dis-
played.
The Setup Utility starts up.
l
If the password is requested, enter the Supervisor Password.
8
Touch [Exit], then double-touch your DVD drive in [Boot Override].
9
Double-touch [Yes]
.
The computer will restart.
10
Touch [Reinstall Windows] and touch [Next].
11
At the confirmation message, touch [YES].
12
At the License Agreement screen, Touch [Yes, I agree to the provi-
sions above and wish to continue!] and touch [Next].
13
When the recovery disc for Windows 8 is used, touch [Next].
When the recovery disc for Windows 7 is used, select the setting and
touch [Next].
l
[Reinstall Windows to the whole Hard Disk to factory default.]
S
elect this option when you want to install Windows to the factory default. After instal-
lation, you can create a new partition. For how to create a new partition, refer to “To
change the partition structure”
(
è
page 21).