Panasonic Toughpad FZ-G1 Operating Instructions - Page 27

Installing Software

Get Panasonic Toughpad FZ-G1 PDF manuals and user guides View all Panasonic Toughpad FZ-G1 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 27 highlights

Installing Software Installing software will return the computer to the default condition. When you install the software, the flash memory data will be erased. Back up important data to other media or an external hard disk before installation. CAUTION l Do not delete the Recovery Partition on the flash memory. The disk space in the partition is not available to store data. To check the Recovery Partition, perform the following methods. A Open "Computer". Long touch [Computer], then touch [Manage]. To open "Computer", proceed as follows on the Start screen. 1. On the Start screen, flick from right side to inside of the screen. 2. Touch [All apps] on the toolbar. 3. Touch [Computer] under "Windows System". Touch (Start) and long touch [Computer], then touch [Manage]. l A standard user needs to enter an administrator password. B Touch [Disk Management]. n Flash memory Recovery You can reinstall the OS that was pre-installed at the time of purchase (Windows 8 or Windows 7). Preparation l Connect the external keyboard. l Remove all peripherals. l Connect the AC adaptor and do not remove it until installation is complete. 1 Perform "Remove everything and reinstall Windows". A Display "Charm" and touch - [Change PC settings] - [General]. B Touch [Get Started] under "Remove everything and reinstall Windows". Installation starts according to the instructions on the screen. (It will take approximately 20 minutes.) l Do not interrupt installation, for example by turning off the computer or performing other operation. Otherwise installation may become unavailable as Windows may not start up or the data may be corrupted. 2 When termination screen is displayed, touch [OK] to turn off the computer. 3 Turn on the computer. l If the password is requested, enter the Supervisor Password. 4 Perform the "First-time Operation" ( page 20). 5 Start the Setup Utility and change the settings as necessary. 6 Perform Windows Update. 7 Clear TPM. A On the Start screen, flick from bottom side to inside of the screen and touch [All apps] on the toolbar. B Touch [Run] under "Windows System", input [tpm.msc] and touch [OK]. C Touch [Clear TPM ...] under "Actions" on the right of the "TPM Manager on Local Com- puter" screen. 27 Useful Information

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
27
Useful Information
Installing software will return the computer to the default condition. When you install the soft-
ware, the flash memory data will be erased.
Back up important data to other media or an external hard disk before installation.
CAUTION
l
Do not delete the Recovery Partition on the flash memory. The disk space in the partition is
not available to store data.
To check the Recovery Partition, perform the following methods.
A
Open “Computer”. Long touch
[Computer], then t
ouch
[Manage].
To open “Computer”, proceed as follows on the Start screen.
1. On the Start screen,
flick from right side to inside of the screen
.
2. Touch
[All apps] on the toolbar.
3. Touch
[Computer] under “Windows System”.
Touch
(Start) and long touch
[Computer], then t
ouch
[Manage].
l
A standard user needs to enter an administrator password.
B
Touch [Disk Management].
n
Flash memory Recovery
You can reinstall the OS that was pre-installed at the time of purchase (Windows 8 or Windows 7).
Preparation
l
Connect the external keyboard.
l
Remove all peripherals.
l
Connect the AC adaptor and do not remove it until installation is complete.
1
Perform “Remove everything and reinstall Windows”.
A
Display “Charm” and touch
- [Change PC settings] - [General].
B
Touch [Get Started] under “Remove everything and reinstall Windows”.
Installation starts according to the instructions on the screen. (It will take approximately
20 minutes.)
l
Do not interrupt installation, for example by turning off the computer or performing other
operation.
Otherwise installation may become unavailable as Windows may not start up or the
data may be corrupted.
2
When termination screen is displayed, touch [OK] to turn off the com-
puter.
3
Turn on the computer.
l
If the password is requested, enter the Supervisor Password.
4
Perform the “First-time Operation” (
è
page 20).
5
Start the Setup Utility and change the settings as necessary.
6
Perform Windows Update.
7
<Only for model with TPM> Clear TPM.
A
On the Start screen, flick from bottom side to inside of the screen and touch [All apps]
on the toolbar.
B
Touch [Run] under “Windows System”, input [tpm.msc] and touch [OK].
C
Touch [Clear TPM ...] under “Actions” on the right of the “TPM Manager on Local Com
-
puter” screen.
Installing Software