Panasonic WJHD220 WJHD220 User Guide - Page 24

Initializing, Initializing All Contents & Setup Data, Initializing Setup Data

Get Panasonic WJHD220 - DIGITAL DISK RECORDER PDF manuals and user guides View all Panasonic WJHD220 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 24 highlights

I Initializing You can initialize all disk contents including image data and/or setup data. G Initializing All Contents & Setup Data Warning! The following are irrevocable procedures. We strongly recommend that you copy important pictures from the hard disk. ON OFF ON 123456 MODE 1. Press the [REC STOP] button or [STOP] button to stop recording or playback. 2. Turn off the power. 3. Set MODE switches #1 through 4 on the rear panel as follows: #1: ON #2: OFF #3: OFF #4: ON 4. Turn on the power. The disk contents and setup data are initialized. NOW FORMATTING HDD FORMAT FINISHED PLEASE TURN OFF MODE SW AND RESTART Notes: • This will take about 40 minutes. • When finished, be sure to carry out step 5. 5. Turn off the power, and return the MODE switches to the previous positions. Then turn on the recorder. 24 G Initializing Setup Data SYSTEM INFORMATION HDD1 HOUR METER 10000H HDD2 HOUR METER 10000H HDD CAPACITY DEFAULT→ XXX.XXG SET→ SYSTEM VERSION X.XX SYSTEM LOGO 1. Open the SYSTEM INFORMATION window, then move the cursor to DEFAULT. 2. Press the JogDial to move the cursor to SET. 3. Press the JogDial. 4. Select YES with the JogDial. YES: Initializing of setup data is enabled. 5. Press the JogDial. SET DONE appears on the monitor after initializing. 6. Press the [SETUP/ESC] button. The cursor moves to DEFAULT. 7. Hold down the [SETUP/ESC] button for 2 seconds to quit the setup. Notes: • After closing the setup menu, the system may automatically restart if any parameter on the network has been changed. • The menu shown above is based on the assumption that an optional HDD is installed in the recorder. As shipped from the factory, the hour meter is set to 1 and the capacity to half. G Initializing Settings for Network Setup Menu 1. Stop recording or playback if applicable, and turn off the power. 2. Set the MODE switches as shown in the figure. ON 123456 MODE 3. Turn on the power. Wait for a few minutes until initializ- ing is completed. 4. Return the MODE switches to the previous positions. Then press the [STOP] button. Note: These procedures reset the settings exclusively for network setup menus: USER SETUP, HOST SETUP, FTP SETUP, MAIL SETUP, and NETWORK VIDEO SETUP.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
24
■
Initializing
You can initialize all disk contents including image data
and/or setup data.
●
Initializing All Contents & Setup Data
Warning!
The following are irrevocable procedures. We
strongly recommend that you copy important pic-
tures from the hard disk.
1. Press the [REC STOP] button or [STOP] button to stop
recording or playback.
2.
Turn off the power.
3. Set MODE switches #1 through 4 on the rear panel as
follows:
#1:
ON
#2:
OFF
#3:
OFF
#4:
ON
4.
Turn on the power.
The disk contents and setup data are initialized.
Notes:
•
This will take about 40 minutes.
•
When finished, be sure to carry out step 5.
5. Turn off the power, and return the MODE switches to
the previous positions. Then turn on the recorder.
●
Initializing Setup Data
1. Open the SYSTEM INFORMATION window, then move
the cursor to DEFAULT.
2.
Press the JogDial to move the cursor to SET.
3.
Press the JogDial.
4.
Select YES with the JogDial.
YES:
Initializing of setup data is enabled.
5.
Press the JogDial.
SET DONE appears on the monitor after initializing.
6.
Press the [SETUP/ESC] button.
The cursor moves to DEFAULT.
7. Hold down the [SETUP/ESC] button for 2 seconds to
quit the setup.
Notes:
•
After closing the setup menu, the system may auto-
matically restart if any parameter on the network
has been changed.
•
The menu shown above is based on the assumption
that an optional HDD is installed in the recorder. As
shipped from the factory, the hour meter is set to 1
and the capacity to half.
●
Initializing Settings for Network
Setup Menu
1. Stop recording or playback if
applicable, and turn off the
power.
2. Set the MODE switches as
shown in the figure.
3. Turn on the power. Wait for a few minutes until initializ-
ing is completed.
4. Return the MODE switches to the previous positions.
Then press the [STOP] button.
Note:
These procedures reset the settings exclusively
for network setup menus: USER SETUP, HOST
SETUP, FTP SETUP, MAIL SETUP, and NETWORK
VIDEO SETUP.
MODE
ON
ON
OFF
1
2
3
4
5
6
NOW FORMATTING HDD
FORMAT FINISHED
PLEASE TURN OFF MODE
SW AND RESTART
SYSTEM INFORMATION
HDD1 HOUR METER
10000H
HDD2 HOUR METER
10000H
HDD CAPACITY
XXX.XXG
DEFAULT
→
SET
→
SYSTEM VERSION
X.XX
SYSTEM LOG
O
MODE
1
2
3
4
5
6
ON