Pfaff C1100 Pro Owner's Manual - Page 34

Cutting The Thread, Replacing The Needle

Get Pfaff C1100 Pro PDF manuals and user guides View all Pfaff C1100 Pro manuals
Add to My Manuals
Save this manual to your list of manuals

Page 34 highlights

CUTTING THE THREAD Press thread snips after finishing sewing and the machine will trim the threads. Use the thread cutter on the face plate to cut the threads. Raise the presser foot. Remove the fabric, draw the threads to the left side of the face plate and cut using the thread cutter. The threads are cut at the proper length to start the next seam. REPLACING THE NEEDLE Attention: Turn power switch to OFF ("O") when replacing the needle ! Change the needle regularly. A bent or damaged needle can cause skipped stitches, damage fabric or break while sewing. To check the needle, place the flat side of the needle on a flat surface. Discard any damaged or bent needles. Before changing the needle, press the needle position button to raise the needle to its highest position. A. Loosen the needle clamp screw and remove the damaged needle. B. With the flat side of the needle facing the back, insert a new needle up as far as it will go. C. Securely tighten the needle clamp screw. 33 GETTING READY

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
CUTTING THE THREAD
Use the thread cutter on the face plate to cut the
threads.
Raise the presser foot. Remove the fabric, draw
the threads to the left side of the face plate and
cut using the thread cutter.
The threads are cut at the proper length to start
the next seam.
Attention:
Turn power switch to OFF (
when replacing the needle !
"O")
Change the needle regularly. A bent or damaged
needle can cause skipped stitches, damage fabric
or break while sewing.
To check the needle, place the flat side of the
needle on a flat surface. Discard any damaged
or bent needles.
Before changing the needle, press the needle
position button to raise the needle to its highest
position.
A. Loosen the needle clamp screw and remove
the damaged needle.
B. With the flat side of the needle facing the back,
insert a new needle up as far as it will go.
C. Securely tighten the needle clamp screw.
REPLACING THE NEEDLE
33
Press thread snips after finishing sewing and the
machine will trim the threads.
GETTING READY