Pfaff creative sensation pro II Manual - Page 33

presser foot

Get Pfaff creative sensation pro II PDF manuals and user guides View all Pfaff creative sensation pro II manuals
Add to My Manuals
Save this manual to your list of manuals

Page 33 highlights

&KDQJLQJWKHpresser foot Remove presser foot Press the presser foot downwards until it disengages from the presser foot holder. Attach presser foot Line up the pins on the foot with the gap underneath the presser foot holder. Press upwards until the foot snaps into place. You can also use the presser foot up/down buttons to raise or lower the presser foot holder. Place the presser foot under the presser foot holder, so that the pins of the foot snap onto the presser foot holder when lowered. $WWDFKLQJWKH'\QDPLFVSULQJIRRW' 1 1. Disengage the IDT™ system (A). Remove the standard presser foot (B). Carefully loosen the C screw (C) until the cross-hole (D) is accessible. A D 2. Hold the foot in front of the needle. Turn the B hand wheel to lower the needle into the hole of 2 the foot and through the needle plate. 3. Turn the foot behind the needle screw (E) and insert the pin of the foot into the cross-hole (D) of the presser foot holder. 4. Push the foot into the hole as far as it will go while tightening the screw (C). 4 To remove the embroidery foot loosen the screw C (C), squeeze the embroidery foot together and pull it out to the right. Tighten the screw. 3 E 2:11 Preparations

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
2:11
A
D
C
B
1
Preparations
presser foot
Remove presser foot
Press the presser foot downwards until it
disengages from the presser foot holder.
Attach presser foot
Line up the pins on the foot with the gap
underneath the presser foot holder. Press upwards
until the foot snaps into place.
You can also use the presser foot up/down buttons
to raise or lower the presser foot holder. Place the
presser foot under the presser foot holder, so that
the pins of the foot snap onto the presser foot holder
when lowered.
1.
Disengage the
IDT
™
system (A). Remove the
standard presser foot (B). Carefully loosen the
screw (C) until the cross-hole (D) is accessible.
2.
Hold the foot in front of the needle. Turn the
hand wheel to lower the needle into the hole of
the foot and through the needle plate.
3.
Turn the foot behind the needle screw (E) and
insert the pin of the foot into the cross-hole (D)
of the presser foot holder.
4.
Push the foot into the hole as far as it will go
while tightening the screw (C).
To remove the embroidery foot loosen the screw
(C), squeeze the embroidery foot together and pull
it out to the right. Tighten the screw.
2
3
4
E
C