Philips HTS5100B User manual - Page 46

SETUPS Note • The range of input number is between 0 and 255. • If you enter a number larger than 255, the number will automatically be 255. • The manually entered number will be saved even if you change the setting to "Auto(DHCP)". • When you enter a wrong number, press [RED] to cancel. (The number will be back to "0".) • If you want to enter 1 or 2 digit number in one cell, press [B] to move on to the next cell. • If the entered IP address or the default gateway or primary DNS number is same as the default setting, IP address setting will be set to "Auto(DHCP)". (The manually entered number will be saved.) • When IP address setting is set to "Manual", the setting of DNS setting will automatically be "Manual" and when IP address setting is set to "Auto(DHCP)", you can set either "Auto(DHCP)" or "Manual" for DNS setting. • Proxy Setting 1) Follow steps 1) to 5) in "Connection Test" on page 44. 2) Use [K / L] to highlight "Enable(Custom)", then press [OK]. 3) Use [K / L] to highlight "Proxy Setting", then press [OK]. 4) Use [K / L] to highlight the desired setting, then press [OK]. • For default settings, select "Do Not Use". • If you need to change the proxy setting as instructed by your Internet service provider to set the designated proxy address and port, select "Use". If you select "Use", follow the following instructions to set the proxy address and proxy port. 4-a) Proxy address setting screen will appear. Enter proxy address. • The keyboard screen will appear. Proxy Setting Proxy Address xxxxxxxx_ 1234567890 abcde f gh i j k l mn o p q r s t u v w x y z . - _ OK Clear All Clear a/A/@ OK [K / L / s / B] : Move the highlight. [the Number buttons] : Enter number. [OK] : Enter the highlighted number/word. *[RED] : Clear the entered number or word. [GREEN] : Clear all the entered numbers or words. [BLUE] : Switch between abc ? ABC ? @!? *[YELLOW] : Set the entered number or word. * These buttons can be used in other network settings. After you enter all correctly, press [YELLOW] to go to the proxy port setting screen. 4-b) Proxy port setting screen will appear. Enter proxy port number with number buttons. Proxy Setting Proxy Port x Clear OK 4-c) After you enter all correctly, press [YELLOW]. • Confirmation message will appear. Select "Yes" to complete the settings. Proxy Address Proxy Port xxxxxxxxxxxxxxx xxxxx Is Setting OK? Yes No 5) Press [BACK U] to go back to the previous screen, or press [HOME ] to go back to the home menu. Note • The range of input number for the port number is between 0 and 65535. (If you enter a number larger than 65535, it will be regarded as 65535.) • For proxy port, the selected ports may be blocked and not be able to use depending on your network environment. • If the proxy address is entered with blank only, proxy server setting will be set to "Do Not Use". • Connection Speed You can set connection speed as your preference. (The default setting is "Auto".) 1) Follow steps 1) to 5) in "Connection Test" on page 44. 2) Use [K / L] to highlight "Enable(Custom)", then press [OK]. 3) Use [K / L] to highlight "Connection Speed", then press [OK]. 4) Use [K / L] to highlight the desired setting, then press [OK]. "Auto": Set the appropriate connection speed automatically, in accordance with your network environment. "10BASE Half": Set the connection speed to "10BASE Half". "10BASE Full": Set the connection speed to "10BASE Full". "100BASE Half": Set the connection speed to "100BASE Half". "100BASE Full": Set the connection speed to "100BASE Full". 5) Press [BACK U] to go back to the previous screen, or press [HOME ] to go back to the home menu. Note • Choose a connection speed in accordance with your network environment. • The network connection may be disabled depending on the device, when the settings are changed. 46 EN