Philips SCD520 User manual - Page 11

Preparing for use - dect baby monitor

Get Philips SCD520 - Avent DECT Baby Monitor Monitoring System PDF manuals and user guides
UPC - 075020005465
View all Philips SCD520 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 11 highlights

ENGLISH 11 , Do not expose the baby monitor to extreme cold or heat or to direct sunlight. , Make sure the baby unit and power cord are always out of reach of the baby (at least 3 feet / 1 meter away). , Never place the baby unit inside the baby's bed or playpen. , Never cover the baby monitor with a towel or blanket. , Never immerse any part of the baby monitor in water or any other liquid. , Never use the baby monitor in moist places or close to water. , Except for the battery compartment, do not open the housing of the baby unit and parent unit in order to prevent electric shock. , Only use the adapters supplied. , The adapters contain a transformer. Do not cut off the adapters to replace them with other plugs, as this will cause a hazardous situation. , If one of the adapters is damaged, always have it replace with one of the original type in order to avoid a hazard. , If you place the parent unit next to a transmitter or other DECT appliance (e.g. a DECT telephone), the connection with the baby unit may be lost. , The temperature sensor only measures the temperature in the baby's room. It cannot be used to control or adjust the temperature in the baby's room. , The power outlet should be located near the appliance and easily accessible. Preparing for use Baby unit You can use the baby unit corded or on non-rechargeable batteries. Even if you are going to use the unit corded, we advise you to insert the nonrechargeable batteries.This guarantees automatic back-up in case of power failure. Corded operation 1 Put the large appliance plug in the baby unit and put the adapter in a wall socket. , The power-on light goes on. Battery operation (non-rechargeable batteries) The baby unit runs on four 1.5V R6 AA batteries (not included).We recommend you to use Philips LR6 PowerLife batteries or an equivalent type. Do not use rechargeable batteries, as the baby unit does not have a charging function. Unplug the baby unit and make sure your hands and the unit are dry when you insert the non-rechargeable batteries. 1 Remove the lid of the compartment for non-rechargeable batteries. 2 Insert four non-rechargeable batteries. Note: Make sure the + and - poles point in the right direction.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
Do not expose the baby monitor to extreme cold or heat or to
direct sunlight.
Make sure the baby unit and power cord are always out of reach of
the baby (at least 3 feet / 1 meter away).
Never place the baby unit inside the baby’s bed or playpen.
Never cover the baby monitor with a towel or blanket.
Never immerse any part of the baby monitor in water or any other
liquid.
Never use the baby monitor in moist places or close to water.
Except for the battery compartment, do not open the housing of the
baby unit and parent unit in order to prevent electric shock.
Only use the adapters supplied.
The adapters contain a transformer. Do not cut off the adapters
to replace them with other plugs, as this will cause a hazardous
situation.
If one of the adapters is damaged, always have it replace with one of
the original type in order to avoid a hazard.
If you place the parent unit next to a transmitter or other DECT
appliance (e.g. a DECT telephone), the connection with the baby unit
may be lost.
The temperature sensor only measures the temperature in the
baby’s room. It cannot be used to control or adjust the temperature
in the baby’s room.
The power outlet should be located near the appliance and easily
accessible.
Preparing for use
Baby unit
You can use the baby unit corded or on non-rechargeable batteries. Even
if you are going to use the unit corded, we advise you to insert the non-
rechargeable batteries. This guarantees automatic back-up in case of power
failure.
Corded operation
1
Put the large appliance plug in the baby unit and put the adapter in a
wall socket.
The power-on light goes on.
Battery operation (non-rechargeable batteries)
The baby unit runs on four 1.5V R6 AA batteries (not included). We
recommend you to use Philips LR6 PowerLife batteries or an equivalent
type.
Do not use rechargeable batteries, as the baby unit does not have a
charging function.
Unplug the baby unit and make sure your hands and the unit are dry
when you insert the non-rechargeable batteries.
1
Remove the lid of the compartment for non-rechargeable batteries.
2
Insert four non-rechargeable batteries.
Note:
Make sure the + and - poles point in the right direction.
,
,
,
,
,
,
,
,
,
,
,
,
,
,
ENGLISH
11