Pioneer DEH-P3000 Owner's Manual - Page 26

BT AUDIO, Setting the rear output and, subwoofer controller, Switching the Ever Scroll, Activating

Get Pioneer DEH-P3000 PDF manuals and user guides View all Pioneer DEH-P3000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 26 highlights

Section 04 Initial Settings Setting the rear output and subwoofer controller This unit's rear output (rear speaker leads output and RCA rear output) can be used for fullrange speaker (REAR SP:FULL/PREOUT:REAR) or subwoofer (REAR SP:SUB W/ PREOUT:SUB W) connection. If you switch the rear output setting to REAR SP:SUB W, you can connect a rear speaker lead directly to a subwoofer without using an auxiliary amp. Initially, the unit is set for rear full-range speaker connection (REAR SP:FULL). When rear output is connected to full range speakers (when REAR SP:FULL is selected), you can connect the RCA subwoofer output to a subwoofer. In this case, you can select whether to use the subwoofer controller's (low pass filter, phase) built-in PREOUT:SUB W or the auxiliary PREOUT:REAR. 1 Use MULTI-CONTROL to select SW CONTROL. 2 Press MULTI-CONTROL to display the setting mode. # Press BACK to return to the previous display. 3 Press MULTI-CONTROL to select the segment you wish to set. Press MULTI-CONTROL repeatedly to switch the segment in the following order: REAR SP (rear speaker setting)-PREOUT (RCA output setting) 4 Use MULTI-CONTROL to select the desired setting. Turn to change the setting. When REAR SP (rear speaker setting) is selected. REAR SP:SUB W (subwoofer)-REAR SP:FULL (full-range speaker) When PREOUT (RCA output setting) is selected. PREOUT:SUB W (subwoofer)-PREOUT:REAR (full-range speaker) # When no subwoofer is connected to the rear output, select REAR SP:FULL. # When a subwoofer is connected to the rear output, set for subwoofer REAR SP:SUB W. Notes ! Even if you change this setting, there is no output unless you turn the subwoofer output on (refer to Using subwoofer output on page 23). ! If you change this setting, subwoofer output in the audio menu return to the factory settings. ! Both rear speaker lead outputs and RCA rear output are switched simultaneously in this setting. Switching the Ever Scroll When Ever Scroll is set to ON, recorded text information scrolls continuously in the display. Set to OFF if you prefer the information to scroll just once. 1 Use MULTI-CONTROL to select EVER SCROLL. 2 Press MULTI-CONTROL to turn the Ever Scroll on. # To turn the Ever Scroll off, press MULTI-CONTROL again. Activating the BT AUDIO source You need to activate the BT AUDIO source in order to use a Bluetooth audio player. ! You can only operate this function when Bluetooth adapter (e.g. CD-BTB200) is connected to this unit. 1 Use MULTI-CONTROL to select BT AUDIO. 2 Press MULTI-CONTROL to turn the BT AUDIO source on. # To turn the BT AUDIO source off, press MULTI-CONTROL again. 26 En

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
Setting the rear output and
subwoofer controller
This unit
’
s rear output (rear speaker leads out-
put and RCA rear output) can be used for full-
range speaker (
REAR SP:FULL
/
PREOUT:REAR
)
or subwoofer (
REAR SP:SUB W
/
PREOUT:SUB W
) connection. If you switch the
rear output setting to
REAR SP:SUB W
, you
can connect a rear speaker lead directly to a
subwoofer without using an auxiliary amp.
Initially, the unit is set for rear full-range speak-
er connection (
REAR SP:FULL
). When rear out-
put is connected to full range speakers (when
REAR SP:FULL
is selected), you can connect
the RCA subwoofer output to a subwoofer. In
this case, you can select whether to use the
subwoofer controller
’
s (low pass filter, phase)
built-in
PREOUT:SUB W
or the auxiliary
PREOUT:REAR
.
1
Use MULTI-CONTROL to select
SW CONTROL.
2
Press MULTI-CONTROL to display the
setting mode.
#
Press
BACK
to return to the previous display.
3
Press MULTI-CONTROL to select the seg-
ment you wish to set.
Press
MULTI-CONTROL
repeatedly to switch
the segment in the following order:
REAR SP
(rear speaker setting)
—
PREOUT
(RCA output setting)
4
Use MULTI-CONTROL to select the de-
sired setting.
Turn to change the setting.
When
REAR SP
(rear speaker setting) is se-
lected.
REAR SP:SUB W
(subwoofer)
—
REAR SP:FULL
(full-range speaker)
When
PREOUT
(RCA output setting) is se-
lected.
PREOUT:SUB W
(subwoofer)
—
PREOUT:REAR
(full-range speaker)
#
When no subwoofer is connected to the rear
output, select
REAR SP:FULL
.
#
When a subwoofer is connected to the rear
output, set for subwoofer
REAR SP:SUB W
.
Notes
!
Even if you change this setting, there is no
output unless you turn the subwoofer output
on (refer to
Using subwoofer output
on page
23).
!
If you change this setting, subwoofer output
in the audio menu return to the factory set-
tings.
!
Both rear speaker lead outputs and RCA rear
output are switched simultaneously in this
setting.
Switching the Ever Scroll
When Ever Scroll is set to ON, recorded text in-
formation scrolls continuously in the display.
Set to OFF if you prefer the information to
scroll just once.
1
Use MULTI-CONTROL to select
EVER SCROLL.
2
Press MULTI-CONTROL to turn the Ever
Scroll on.
#
To turn the Ever Scroll off, press
MULTI-CONTROL
again.
Activating the
BT AUDIO
source
You need to activate the
BT AUDIO
source in
order to use a Bluetooth audio player.
!
You can only operate this function when
Bluetooth adapter (e.g. CD-BTB200) is con-
nected to this unit.
1
Use MULTI-CONTROL to select
BT AUDIO.
2
Press MULTI-CONTROL to turn the
BT AUDIO source on.
#
To turn the
BT AUDIO
source off, press
MULTI-CONTROL
again.
Initial Settings
En
26
Section
04