Pioneer DEH-P7800MP Owner's Manual - Page 58

Using subwoofer output, Audio Adjustments, Adjusting subwoofer settings, Adjusting low pass filter

Get Pioneer DEH-P7800MP PDF manuals and user guides
UPC - 012562793917
View all Pioneer DEH-P7800MP manuals
Add to My Manuals
Save this manual to your list of manuals

Page 58 highlights

Section 13 Audio Adjustments Using subwoofer output This unit is equipped with a subwoofer output which can be turned on or off. When a subwoofer is connected to this unit, turn the subwoofer output on. The subwoofer output phase can be switched between normal and reverse. 1 Use MULTI-CONTROL to select Subwoofer1. Subwoofer1 appears in the display. # You can also select the subwoofer setting menu by pressing SW on the unit. 2 Press MULTI-CONTROL to turn subwoofer output on. ON appears in the display. Subwoofer output is now on. # To turn subwoofer output off, press MULTI-CONTROL again. 3 Push MULTI-CONTROL left or right to select stereo or monaural. Push MULTI-CONTROL left to select monaural and MONO appears in the display. Push MULTI-CONTROL right to select stereo and STEREO appears in the display. Adjusting subwoofer settings When the subwoofer output is on, you can adjust the cut-off frequency and the output level of the subwoofer. 1 Use MULTI-CONTROL to select Subwoofer2. Subwoofer2 appears in the display. # You can also select the subwoofer setting menu by pressing SW on the unit. # When the subwoofer output is on, you can select Subwoofer2. 2 Push MULTI-CONTROL left or right to select cut-off frequency. Each time MULTI-CONTROL is pushed left or right, cut-off frequencies are selected in the following order: 50-63-80-100-125-160-200 (Hz) Only frequencies lower than those in the selected range are outputted from the subwoofer. 3 Push MULTI-CONTROL up or down to adjust the output level of the subwoofer. Each time MULTI-CONTROL is pushed up or down, subwoofer level increases or decreases. +6 to -24 is displayed as the level is increased or decreased. Adjusting low pass filter attenuation slope When the subwoofer output is on, you can adjust the continuity of sound between speaker units. 1 Use MULTI-CONTROL to select Subwoofer3. Subwoofer3 appears in the display. # You can also select the subwoofer setting menu by pressing SW on the unit. # When the subwoofer output is on, you can select Subwoofer3. 2 Push MULTI-CONTROL up or down to select the phase of subwoofer output. Push MULTI-CONTROL up to select normal phase and appears in the display. Push MULTI-CONTROL down to select reverse phase and appears in the display. 3 Push MULTI-CONTROL left or right to select slope. Each time MULTI-CONTROL is pushed left or right, slopes are selected in the following order: -18- -12- -6 (dB/oct.) 58 En

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
Using subwoofer output
This unit is equipped with a subwoofer output
which can be turned on or off. When a sub-
woofer is connected to this unit, turn the sub-
woofer output on.
The subwoofer output phase can be switched
between normal and reverse.
1
Use MULTI-CONTROL to select
Subwoofer1.
Subwoofer1
appears in the display.
#
You can also select the subwoofer setting
menu by pressing
SW
on the unit.
2
Press MULTI-CONTROL to turn subwoo-
fer output on.
ON
appears in the display. Subwoofer output
is now on.
#
To turn subwoofer output off, press
MULTI-CONTROL
again.
3
Push MULTI-CONTROL left or right to
select stereo or monaural.
Push
MULTI-CONTROL
left to select monaural
and
MONO
appears in the display. Push
MULTI-CONTROL
right to select stereo and
STEREO
appears in the display.
Adjusting subwoofer settings
When the subwoofer output is on, you can ad-
just the cut-off frequency and the output level
of the subwoofer.
1
Use MULTI-CONTROL to select
Subwoofer2.
Subwoofer2
appears in the display.
#
You can also select the subwoofer setting
menu by pressing
SW
on the unit.
#
When the subwoofer output is on, you can se-
lect
Subwoofer2
.
2
Push MULTI-CONTROL left or right to
select cut-off frequency.
Each time
MULTI-CONTROL
is pushed left or
right, cut-off frequencies are selected in the
following order:
50
—
63
—
80
—
100
—
125
—
160
—
200
(Hz)
Only frequencies lower than those in the se-
lected range are outputted from the subwoo-
fer.
3
Push MULTI-CONTROL up or down to
adjust the output level of the subwoofer.
Each time
MULTI-CONTROL
is pushed up or
down, subwoofer level increases or decreases.
+6
to
–
24
is displayed as the level is increased
or decreased.
Adjusting low pass filter
attenuation slope
When the subwoofer output is on, you can ad-
just the continuity of sound between speaker
units.
1
Use MULTI-CONTROL to select
Subwoofer3.
Subwoofer3
appears in the display.
#
You can also select the subwoofer setting
menu by pressing
SW
on the unit.
#
When the subwoofer output is on, you can se-
lect
Subwoofer3
.
2
Push MULTI-CONTROL up or down to
select the phase of subwoofer output.
Push
MULTI-CONTROL
up to select normal
phase and
appears in the display. Push
MULTI-CONTROL
down to select reverse
phase and
appears in the display.
3
Push MULTI-CONTROL left or right to
select slope.
Each time
MULTI-CONTROL
is pushed left or
right, slopes are selected in the following
order:
–
18
—
–
12
—
–
6
(dB/oct.)
Audio Adjustments
En
58
Section
13