Pioneer DJM-900NXS Operating Instructions - Page 13

g DIGITAL, CD/LINE, PHONO, LINE, USB */* selector switch (page 14) Select the input source of each channel from the components connected to this unit. F DELAY, ECHO, SPIRAL, REVERB, TRANS, FILTER, FLANGER, PHASER, ROBOT, MELODIC, SLIP ROLL, ROLL, REV ROLL, SND/RTN (MIDI LFO) selector switch (page 16) Switches the BEAT EFFECT effect type. h TRIM control (page 14) Adjusts the level of audio signals input in each channel. G 1, 2, 3, 4, MIC, CF.A, CF.B, MASTER selector switch (page 16) Switches the channel to which the BEAT EFFECT is to be applied. i EQ/ISO (HI, MID, LOW) controls (page 14) These adjust the sound quality of the different channels. H TIME control (page 16) Adjust the BEAT EFFECT's time parameter. Operations j Channel Level Indicator (page 14) Displays the sound level of the different channels before passing through the channel faders. I LEVEL/DEPTH control (page 16) Adjusts the BEAT EFFECT's quantitative parameter. k COLOR controls (page 15) These change the parameters of the SOUND COLOR FX of the different channels. J ON/OFF button (page 16) Turns the BEAT EFFECT function on/off. Do not pull on the channel fader and crossfader knobs with excessive force. The knobs are not designed to be removed. Pulling the knobs strongly may result in damaging the unit. l Channel Fader (page 14) Adjusts the level of audio signals output in each channel. m CROSS FADER ASSIGN (A, THRU, B) selector switch (page 14) Set the output destination of each channel to [A] or [B]. n Crossfader (page 14) Outputs audio signals assigned by the crossfader assign switch corresponding to the curve characteristics selected by [CROSS FADER] (Crossfader Curve Selector Switch). o MASTER LEVEL controls (page 14) Adjusts the sound level output from the [MASTER] channel. p Master Level Indicator (page 14) Displays the sound level output from the [MASTER] channel. q BALANCE controls (page 15) Adjusts the left/right balance of the sound output from the [MASTER1] terminals, etc. r MONO, STEREO selector switch (page 15) Switches the sound output from the [MASTER1] terminals, etc., between monaural and stereo. s BOOTH MONITOR controls (page 15) Adjusts the level of audio signals output at the [BOOTH] terminal. t EQ CURVE (ISOLATOR, EQ) selector switch (page 14) Switches the function of the [EQ/ISO (HI, MID, LOW)] controls. u CH FADER ( , , , ) selector switch (page 14) , ) selector switch (page 14) Switches the channel fader's curve characteristics. v CROSS FADER ( This switches the crossfader curve characteristics. w ON/OFF (UTILITY) button - ON/OFF: Turns the MIDI function on/off (page 17). - UTILITY: Displays the [USER SETUP] or [CLUB SETUP] screen (page 23). x START/STOP button (page 17) Sends the MIDI start/MIDI stop signals. y LFO FORM (WAKE UP) button - LFO FORM: When [MIDI LFO] is selected at BEAT EFFECT, the MIDI signal's waveform switches each time the button is pressed (page 20). - WAKE UP: Cancels the auto standby mode (page 23). z Main unit display A X-PAD (page 16) Adjusts the quantitative parameter of the BEAT EFFECT function. B BEAT c, d buttons (page 16) Sets the beat fraction for synchronizing the effect sound. C TAP (ENTER) button - TAP: When the BPM measurement mode is set to [TAP], the BPM is input manually by tapping the button with a finger (page 16). - ENTER: Used to change this unit's settings (page 23). ! Used to change this unit's settings (page 23). ! When the QUANTIZE function is turned on for BEAT EFFECT, the effect is applied to the sound without going off tempo when the currently playing track. (page 16). D QUANTIZE button E AUTO/TAP button (page 16) Switches the BPM measurement mode. En 13