Pioneer DJM-900NXS Operating Instructions - Page 19

Pioneer DJM-900NXS Manual

Get Pioneer DJM-900NXS PDF manuals and user guides View all Pioneer DJM-900NXS manuals
Add to My Manuals
Save this manual to your list of manuals

Page 19 highlights

FILTER1 The filter's cutoff frequency changes according to the beat fraction set with the [BEAT c, d] buttons. BEAT c, d buttons (parameter 1) TIME control (parameter 2) LEVEL/DEPTH control (parameter 3) X-PAD (parameter 4) This sets the way in which the recorded sound is played. This sets the way in which the recorded sound is played. This sets the balance between the original sound and the recorded sound. This sets the way in which the recorded sound is played. Frequency BEAT c, d buttons (parameter 1) TIME control (parameter 2) LEVEL/DEPTH control (parameter 3) X-PAD (parameter 4) Use these to set the cycle for moving the cut-off frequency as a time of 1/4 - 64/1 with respect to the time of one beat of the BPM. Use this to set the cycle at which the cut-off frequency is moved. 10 to 32000 (ms) The further the control is turned clockwise, the more the effect is stressed. The cycle at which the cut-off frequency is moved fluctuates finely. SLIP ROLL1 2 The sound being input at the point when the [ON/OFF] is pressed is recorded, and the recorded sound is output repeatedly according to the beat fraction set with the [BEAT c, d] buttons. When the effect time changes, the input sound is recorded again. Original Types of effects Effect turned on Roll Changed from 1/2 to 1/1 FLANGER1 A 1-cycle flanger effect is produced according to the beat fraction set with the [BEAT c, d] buttons. Short delay 1/2 repeat BEAT c, d buttons (parameter 1) TIME control (parameter 2) LEVEL/DEPTH control (parameter 3) 1/1 repeat Use these to set an effect time of 1/16 - 16/1 with respect to the time of one beat of the BPM. Use this to set the effect time. 10 to 4000 (ms) Use this to set the balance between the original sound and ROLL. Use this to set the effect time. Time Cycle BEAT c, d buttons (parameter 1) TIME control (parameter 2) Use these to set the 1/4 - 64/1 effect time with respect to the time of one beat of the BPM. Use this to set the cycle by which the flanger effect moves. 10 to 32000 (ms) The further the control is turned clockwise, the more the effect is stressed. When turned all the way counterclockwise, only the original sound is output. The cycle at which the flanger effect is moved fluctuates finely. X-PAD (parameter 4) ROLL1 2 The sound being input at the point when the [ON/OFF] is pressed is recorded, and the recorded sound is output repeatedly according to the beat fraction set with the [BEAT c, d] buttons. Original LEVEL/DEPTH control (parameter 3) X-PAD (parameter 4) PHASER1 The phaser effect changes according to the beat fraction set with the [BEAT c, d] buttons. Phase shift Effect turned on 1/1 roll Repeated BEAT c, d buttons (parameter 1) TIME control (parameter 2) Use these to set the cycle for moving the phaser effect as of time of 1/4 - 64/1 with respect to the time of one beat of the BPM. This sets the cycle by which the phaser effect is moved. 10 to 32000 (ms) The further the control is turned clockwise, the more the effect is stressed. When turned all the way counterclockwise, only the original sound is output. The cycle at which the phaser effect is moved fluctuates finely. LEVEL/DEPTH control (parameter 3) X-PAD (parameter 4) Use these to set an effect time of 1/16 - 16/1 with respect to the time of one beat of the BPM. Use this to set the effect time. 10 to 4000 (ms) Use this to set the balance between the original sound and ROLL. Use this to set the effect time. Time Cycle BEAT c, d buttons (parameter 1) TIME control (parameter 2) LEVEL/DEPTH control (parameter 3) X-PAD (parameter 4) REV ROLL1 2 The sound being input at the point when the [ON/OFF] button is pressed is recorded, and the recorded sound is reversed then output repeatedly according to the beat fraction set with the [BEAT c, d] buttons. Original ROBOT1 The original sound is changed to a sound like one produced by a robot. BEAT c, d buttons (parameter 1) TIME control (parameter 2) LEVEL/DEPTH control (parameter 3) X-PAD (parameter 4) Use these to set the degree of the effect sound, from -100 - 100

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
En
19
Types of effects
FILTER
1
The filter’s cutoff frequency changes according to the beat fraction set with the
[
BEAT
c
,
d
] buttons.
Frequency
BEAT
c
,
d
buttons (param-
eter 1)
Use these to set the cycle for moving the cut-off frequency as a
time of
1/4
–
64/1
with respect to the time of one beat of the BPM.
TIME
control (parameter 2)
Use this to set the cycle at which the cut-off frequency is moved.
10
to
32000
(ms)
LEVEL/
DEPTH
control
(parameter 3)
The further the control is turned clockwise, the more the effect
is stressed.
X-PAD
(parameter 4)
The cycle at which the cut-off frequency is moved fluctuates
finely.
FLANGER
1
A 1-cycle flanger effect is produced according to the beat fraction set with the [
BEAT
c
,
d
] buttons.
Short delay
Cycle
Time
BEAT
c
,
d
buttons (param-
eter 1)
Use these to set the
1/4
–
64/1
effect time with respect to the
time of one beat of the BPM.
TIME
control (parameter 2)
Use this to set the cycle by which the flanger effect moves.
10
to
32000
(ms)
LEVEL/
DEPTH
control
(parameter 3)
The further the control is turned clockwise, the more the effect
is stressed.
When turned all the way counterclockwise, only the original
sound is output.
X-PAD
(parameter 4)
The cycle at which the flanger effect is moved fluctuates finely.
PHASER
1
The phaser effect changes according to the beat fraction set with the [
BEAT
c
,
d
]
buttons.
Cycle
Phase shift
Time
BEAT
c
,
d
buttons (param-
eter 1)
Use these to set the cycle for moving the phaser effect as of time
of
1/4
–
64/1
with respect to the time of one beat of the BPM.
TIME
control (parameter 2)
This sets the cycle by which the phaser effect is moved.
10
to
32000
(ms)
LEVEL/
DEPTH
control
(parameter 3)
The further the control is turned clockwise, the more the effect
is stressed.
When turned all the way counterclockwise, only the original
sound is output.
X-PAD
(parameter 4)
The cycle at which the phaser effect is moved fluctuates finely.
ROBOT
1
The original sound is changed to a sound like one produced by a robot.
BEAT
c
,
d
buttons (param-
eter 1)
Use these to set the degree of the effect sound, from
-100
–
100
%.
TIME
control (parameter 2)
Use this to set the degree of the effect sound.
-100
–
100
(%)
LEVEL/
DEPTH
control
(parameter 3)
Sets the balance between the original sound and the effect
sound.
X-PAD
(parameter 4)
This changes the degree of the effect sound.
MELODIC
1
2
The mid-range of the sound being input at the point when the [
ON/OFF
] button is
pressed is recorded, and the recorded sound is output according to the level of the
sound being input.
BEAT
c
,
d
buttons (param-
eter 1)
This sets the way in which the recorded sound is played.
TIME
control (parameter 2)
This sets the way in which the recorded sound is played.
LEVEL/
DEPTH
control
(parameter 3)
This sets the balance between the original sound and the
recorded sound.
X-PAD
(parameter 4)
This sets the way in which the recorded sound is played.
SLIP ROLL
1
2
The sound being input at the point when the [
ON/OFF
] is pressed is recorded, and
the recorded sound is output repeatedly according to the beat fraction set with the
[
BEAT
c
,
d
] buttons.
When the effect time changes, the input sound is recorded again.
1/1 repeat
1/2 repeat
Original
Roll
Changed from 1/2
to 1/1
Effect turned on
BEAT
c
,
d
buttons (param-
eter 1)
Use these to set an effect time of
1/16
–
16/1
with respect to the
time of one beat of the BPM.
TIME
control (parameter 2)
Use this to set the effect time.
10
to
4000
(ms)
LEVEL/
DEPTH
control
(parameter 3)
Use this to set the balance between the original sound and
ROLL
.
X-PAD
(parameter 4)
Use this to set the effect time.
ROLL
1
2
The sound being input at the point when the [
ON/OFF
] is pressed is recorded, and
the recorded sound is output repeatedly according to the beat fraction set with the
[
BEAT
c
,
d
] buttons.
Effect turned on
Repeated
Original
1/1 roll
BEAT
c
,
d
buttons (param-
eter 1)
Use these to set an effect time of
1/16
–
16/1
with respect to the
time of one beat of the BPM.
TIME
control (parameter 2)
Use this to set the effect time.
10
to
4000
(ms)
LEVEL/
DEPTH
control
(parameter 3)
Use this to set the balance between the original sound and
ROLL
.
X-PAD
(parameter 4)
Use this to set the effect time.
REV ROLL
1
2
The sound being input at the point when the [
ON/OFF
] button is pressed is
recorded, and the recorded sound is reversed then output repeatedly according to
the beat fraction set with the [
BEAT
c
,
d
] buttons.
Effect turned on
Reversed and repeated
Original
1/1 reverse
roll
BEAT
c
,
d
buttons (param-
eter 1)
Use these to set an effect time of
1/16
–
16/1
with respect to the
time of one beat of the BPM.
TIME
control (parameter 2)
Use this to set the effect time.
10
to
4000
(ms)
LEVEL/
DEPTH
control
(parameter 3)
Use this to set the balance between the original sound and
ROLL
.
X-PAD
(parameter 4)
Use this to set the effect time.