Pioneer PDP-425CMX User Manual - Page 20

Power cord connection

Get Pioneer PDP-425CMX PDF manuals and user guides View all Pioneer PDP-425CMX manuals
Add to My Manuals
Save this manual to your list of manuals

Page 20 highlights

English Installation and Connections Power cord connection Connect the power cord after all component connections have been completed. AC IN Note Regarding the audio cable, attach the supplied ferrite core. If you do not do this, this monitor will not conform to mandatory FCC standards. Wind the audio cable (not supplied) around the ferrite core once, and then fasten the catch. Audio cable (not supplied) 1 Ferrite core 2 1 Connect the power cord to this unit. 2 Plug the power cord into a power outlet. CAUTION ÷ Use only the power cord provided. ÷ For the Plasma Display, a three-core power cord with a ground terminal is used for efficiency protection. Always be sure to connect the power cord to a three-pronged grounded outlet and make sure that the cord is properly grounded. If you use a power source converter plug, use an outlet with a ground terminal and screw down the ground line. NO! Do not use a power supply voltage other than that indicated (AC 100 - 120 V, 50/60 Hz) as this may cause fire or electric shock. Attaching the ferrite cores To help prevent noise, attach the accessory ferrite cores to the both connector ends of the power cord as shown in the accompanying illustration. Use the provided cable tie to prevent the ferrite core from slipping on the cable. Installation and Connections To power outlet AC power cord 14 En Ferrite core Cable tie To AC IN As close as possible

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
14
En
Installation and Connections
English
Installation and Connections
Power cord connection
Connect the power cord after all component connections
have been completed.
AC IN
1
Connect the power cord to this unit.
2
Plug the power cord into a power outlet.
CAUTION
÷
Use only the power cord provided.
÷
For the Plasma Display, a three-core power cord with a ground
terminal is used for efficiency protection.
Always be sure to connect the power cord to a three-pronged
grounded outlet and make sure that the cord is properly
grounded. If you use a power source converter plug, use an
outlet with a ground terminal and screw down the ground line.
NO!
Do not use a power supply voltage other than that indicated (AC
100 - 120 V, 50/60 Hz) as this may cause fire or electric shock.
Attaching the ferrite cores
To help prevent noise, attach the accessory ferrite cores
to the both connector ends of the power cord as shown
in the accompanying illustration. Use the provided cable
tie to prevent the ferrite core from slipping on the cable.
1
2
Ferrite core
Cable tie
AC power cord
To power
outlet
As close as possible
To AC IN
Note
Regarding the audio cable, attach the supplied ferrite core. If you
do not do this, this monitor will not conform to mandatory FCC
standards.
Wind the audio cable (not supplied) around the ferrite core once,
and then fasten the catch.
Audio cable (not supplied)
Ferrite core