Pioneer VSX-516-S Operating Instructions - Page 50

Additional information - reset

Get Pioneer VSX-516-S PDF manuals and user guides View all Pioneer VSX-516-S manuals
Add to My Manuals
Save this manual to your list of manuals

Page 50 highlights

11 Additional information Chapter 11: Additional information Troubleshooting Incorrect operations are often mistaken for trouble and malfunctions. If you think that there is something wrong with this component, check the points below. Sometimes the trouble may lie in another component. Investigate the other components and electrical appliances being used. If the trouble cannot be rectified even after exercising the checks listed below, ask your nearest Pioneer authorized service center or your dealer to carry out repair work. • If the unit does not operate normally due to external effects such as static electricity disconnect the power plug from the outlet and insert again to return to normal operating conditions. Problem The power does not turn on. Remedy • Disconnect the power plug from the outlet, and insert again. • Make sure there are no loose strands of speaker wire touching the rear panel. This could cause the receiver to shut off automatically. • If the power shuts off automatically, take the unit to your nearest Pioneer authorized service center or your dealer for servicing. • The unit may have been switched on using the wrong voltage setting. Make sure you switch the VOLTAGE SELECTOR on the rear panel to the right voltage for your country or region, then reset the unit (page 52) before switching on again. No sound is output when a function is selected. • Make sure the component is connected correctly (refer to Connecting up on page 11). • Press MUTE on the remote control to turn muting off. No image is output when a function is selected. • Make sure the component is connected correctly (refer to Connecting up on page 11). • Select the correct component (use the input select buttons). Considerable noise in radio broadcasts. • Connect the antenna (page 16) and adjust the position for best reception. • Route any loose cables away from the antenna terminals and wires. • Fully extend the FM wire antenna, position for best reception, and secure to a wall (or connect an outdoor FM antenna). • Connect an additional internal or external AM antenna (page 16). • Turn off equipment causing interference or move it away from the receiver (or move antennas farther away from equipment causing noise). Broadcast stations cannot be • Connect an outdoor antenna (refer to page 16). selected automatically. 50 En

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
Additional information
11
50
En
Chapter 11:
Additional information
Troubleshooting
Incorrect operations are often mistaken for trouble and malfunctions. If you think that there is
something wrong with this component, check the points below. Sometimes the trouble may lie in
another component. Investigate the other components and electrical appliances being used. If the
trouble cannot be rectified even after exercising the checks listed below, ask your nearest Pioneer
authorized service center or your dealer to carry out repair work.
•
If the unit does not operate normally due to external effects such as static electricity disconnect
the power plug from the outlet and insert again to return to normal operating conditions.
Problem
Remedy
The power does not turn on.
• Disconnect the power plug from the outlet, and insert again.
• Make sure there are no loose strands of speaker wire touching the
rear panel. This could cause the receiver to shut off automatically.
• If the power shuts off automatically, take the unit to your nearest
Pioneer authorized service center or your dealer for servicing.
• The unit may have been switched on using the wrong voltage
setting. Make sure you switch the
VOLTAGE SELECTOR
on the rear
panel to the right voltage for your country or region, then reset the
unit (page 52) before switching on again.
No sound is output when a
function is selected.
• Make sure the component is connected correctly (refer to
Connecting up
on page 11).
• Press
MUTE
on the remote control to turn muting off.
No image is output when a
function is selected.
• Make sure the component is connected correctly (refer to
Connecting up
on page 11).
• Select the correct component (use the input select buttons).
Considerable noise in radio
broadcasts.
• Connect the antenna (page 16) and adjust the position for best
reception.
• Route any loose cables away from the antenna terminals and wires.
• Fully extend the FM wire antenna, position for best reception, and
secure to a wall (or connect an outdoor FM antenna).
• Connect an additional internal or external AM antenna (page 16).
• Turn off equipment causing interference or move it away from the
receiver (or move antennas farther away from equipment causing
noise).
Broadcast stations cannot be
selected automatically.
• Connect an outdoor antenna (refer to page 16).