Pioneer VSX-52TX Service Manual - Page 116

HOW TO DIAGNOSE THE AMPLIFIER CN2101-2104 on the SP/PS Assy. And limit failure CH.

Get Pioneer VSX-52TX PDF manuals and user guides View all Pioneer VSX-52TX manuals
Add to My Manuals
Save this manual to your list of manuals

Page 116 highlights

1 2 3 4 7.1.2 HOW TO DIAGNOSE THE AMPLIFIER SECTION When DC detection worked (STBY IND. flashes for a long time) in the protection circuit of foregoing section (or there is not the A speaker output, probably only 1CH), failure (damage) of the power amplifier section is considered. Because this receiver cannot diagnose the amplifier section by an electricity state by structure, please diagnose it in the following steps. Caution: When release the STBY (flashes) state before repair, Because there is the case that the damage progresses when turns the power on once again, please be careful. B • According to a symptom, perform the following confirmation beforehand. 1. Are not Fuse and IC protector opening it? 2-a. When can turn on electricity, confirm that supply voltage of the point that can measure is appropriate. 2-b. Furthermore, confirm that voltage ((in a no signal) DC and the appropriate signal output) between GND and R2008R2014 on the SP/PS Assy (Either of the amplifier side and the speaker terminal side is possible) (Or remove either of CN2101-2104) on the SP/PS Assy. And limit failure CH. If was able to limit failure CH, diagnose the CH in the following steps. C • Use the tester basically and check that each part is not damaged (resistance value / open / short circuit). About parts with damaged possibility, explain FL ch to an example in order. 1. R4131, R4132 (ACN7132: 0.047 Ω, 0.5W chip drain resistor) IC 4102, IC4103 (PBD001A: Nch, PBD002A: Pch output POWER MOS Tr.) /POWER AMP-L Assy 2. R4119 (ACN7121: 0.18 Ω .5W ×2 cement source resistor) R4117, R4118 (RS1/16S471J: 470 Ω chip resistor for D protection circuit) D4101, D4103 (UDZS10B: 10V Zener diode for current limiting) D4102, D4104 (1SS355: Small signal diodes same as above) R4110, R4111 (RS1/16S560J: 56 Ω chip gate resistor) R4106, R4107 (RS1/16S101J:100 Ω chip IC4101 power filter resistor) /POWER AMP-L Assy 3. IC4101 (PA9010A: Power amplifier with output current bias Voltage step HIC) /POWER AMP-L Assy E 4. Q2231 (2SA1514K) /VH TR Assy Q2232 (2SC3906K) /VH TR Assy Q2233 (2SA1837D1) /VH TR Assy Q2234 (2SC4793D1) /VH TR Assy F 116 VSX-52TX 1 2 3 4

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
VSX-52TX
116
1
2
3
4
1
2
3
4
C
D
F
A
B
E
7.1.2
HOW TO DIAGNOSE THE AMPLIFIER SECTION
When DC detection worked (STBY IND. flashes for a long time)
in the protection circuit of foregoing section (or there is not the
speaker output, probably only 1CH), failure (damage) of the
power amplifier section is considered.
Because this receiver cannot diagnose the amplifier section by an
electricity state by structure, please diagnose it in the following
steps.
Caution:
When release the STBY (flashes) state before repair, Because
there is the case that the damage progresses when turns the power
on once again, please be careful.
•
According to a symptom, perform the following
confirmation beforehand.
1.
Are not Fuse and IC protector opening it?
2-a.
When can turn on electricity, confirm that supply voltage of
the point that can measure is appropriate.
2-b.
Furthermore, confirm that voltage ((in a no signal) DC and
the appropriate signal output) between GND and R2008-
R2014 on the SP/PS Assy (Either of the amplifier side and
the speaker terminal side is possible) (Or remove either of
CN2101-2104) on the SP/PS Assy. And limit failure CH.
If was able to limit failure CH, diagnose the CH in the following
steps.
• Use the tester basically and check that each part is
not damaged (resistance value / open / short circuit).
About parts with damaged possibility, explain FL ch to an
example in order.
1.
R4131, R4132
(ACN7132: 0.047
Ω
, 0.5W chip drain resistor)
IC 4102, IC4103 (PBD001A: Nch, PBD002A: Pch output
POWER MOS Tr.) /POWER AMP-L Assy
2.
R4119 (ACN7121: 0.18
Ω
.5W
×
2 cement source resistor)
R4117, R4118 (RS1/16S471J: 470
Ω
chip resistor for
protection circuit)
D4101, D4103 (UDZS10B: 10V Zener diode for current
limiting)
D4102, D4104
(1SS355: Small signal diodes same as above)
R4110, R4111
(RS1/16S560J: 56
Ω
chip gate resistor)
R4106, R4107 (RS1/16S101J:100
Ω
chip IC4101 power filter
resistor) /POWER AMP-L Assy
3.
IC4101 (PA9010A: Power amplifier with output current bias
Voltage step HIC) /POWER AMP-L Assy
4.
Q2231 (2SA1514K)
/VH TR Assy
Q2232 (2SC3906K)
/VH TR Assy
Q2233 (2SA1837D1)
/VH TR Assy
Q2234 (2SC4793D1)
/VH TR Assy